Technisat Cablestar HD2, jak uruchomić?

[max95100]

Witam posiadam kartę DVB-C cablestar HD2 i mam problem z uruchomieniem ją na linuxie, znalazłem informacje na temat jej odpalenia tutaj:
http://www.linuxtv.org/wiki/index.php/T ... leStar_HD2
ale chyba linki na tej stronie wygasły bo nic mi nie wychodzi. Jest jakiś inny sposób na odpalenie tej karty pod ubuntu??

[luk1don]

Kod: Zaznacz cały

lspci

pokaż wynik tej komendy

[max95100]

oto co mi pokazało

00:00.0 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a1)
00:01.0 ISA bridge: NVIDIA Corporation MCP61 LPC Bridge (rev a2)
00:01.1 SMBus: NVIDIA Corporation MCP61 SMBus (rev a2)
00:01.2 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a2)
00:02.0 USB controller: NVIDIA Corporation MCP61 USB 1.1 Controller (rev a3)
00:02.1 USB controller: NVIDIA Corporation MCP61 USB 2.0 Controller (rev a3)
00:04.0 PCI bridge: NVIDIA Corporation MCP61 PCI bridge (rev a1)
00:05.0 Audio device: NVIDIA Corporation MCP61 High Definition Audio (rev a2)
00:06.0 IDE interface: NVIDIA Corporation MCP61 IDE (rev a2)
00:07.0 Bridge: NVIDIA Corporation MCP61 Ethernet (rev a2)
00:08.0 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2)
00:09.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:06.0 Multimedia controller: Philips Semiconductors SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)
01:08.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI Bridge Controller [Ver 1.0] (rev 01)
02:00.0 VGA compatible controller: NVIDIA Corporation G94 [GeForce 9600 GT] (rev a1)

[luk1don]

Kod: Zaznacz cały

sudo lspci -vv -s 01:08.0

-- niedziela, 6 stycznia 2013, 15:10 --

Dasz wynik tej komendy czy nie? (kopiuj-wklej)

[max95100]

włączyła mi się aktualzacja ubuntu i nie mogłem odpalić terminala

01:08.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI Bridge Controller [Ver 1.0] (rev 01)
Subsystem: Device 1ae4:0002
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fdfff000 (32-bit, prefetchable)
Kernel driver in use: Mantis
Kernel modules: mantis

[luk1don]

Karta sobie działa i korzysta z modułu:

Kod: Zaznacz cały

Kernel driver in use: Mantis
Kernel modules: mantis

Pokaż jeszcze:

Kod: Zaznacz cały

lsmod |grep mantis

[max95100]

mantis 23328 0
mantis_core 40435 1 mantis
dvb_core 110619 1 mantis_core
rc_core 26412 12 rc_medion_x10,ati_remote,ir_lirc_codec,ir_mce_kbd_decoder,saa7134,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,mantis_core,ir_nec_decoder

[luk1don]

No i działasz na tym dvb czy nie?

-- niedziela, 6 stycznia 2013, 15:41 --

Wiesz jak ustawić kanały?

-- niedziela, 6 stycznia 2013, 15:44 --

???

[max95100]

nie bardzo wiem jakim programem obsłużę kartę DVB bo napewno nie tv time

[luk1don]

Możesz używać co bądź. Ja używam VLC.
Zrób tak (przykładowo) bo nie wiem co masz poinstalowane itd.:

Kod: Zaznacz cały

sudo apt-get install dvb-apps dvbstream w-scan vlc

Kod: Zaznacz cały

w_scan -c PL -X > channels.conf

Kod: Zaznacz cały

vlc channels.conf

[max95100]

po

w_scan -c PL -X > channels.conf

mam

w_scan version 20120605 (compiled for DVB API 5.5)
using settings for POLAND
DVB aerial
DVB-T Europe
scan type TERRESTRIAL, channellist 4
output format czap/tzap/szap/xine
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
main:3220: FATAL: ***** NO USEABLE TERRESTRIAL CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

[luk1don]

Poprzedż sudo

[max95100]

teraz mam

w_scan version 20120605 (compiled for DVB API 5.5)
using settings for POLAND
DVB aerial
DVB-T Europe
scan type TERRESTRIAL, channellist 4
output format czap/tzap/szap/xine
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
/dev/dvb/adapter0/frontend0 -> "Philips TDA10023 DVB-C" doesnt support TERRESTRIAL -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE TERRESTRIAL CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

[luk1don]

Kod: Zaznacz cały

sudo w_scan -o 7

[max95100]

cały czas to samo

w_scan version 20120605 (compiled for DVB API 5.5)
guessing country 'PL', use -c <country> to override
using settings for POLAND
DVB aerial
DVB-T Europe
scan type TERRESTRIAL, channellist 4
output format vdr-1.7
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
/dev/dvb/adapter0/frontend0 -> "Philips TDA10023 DVB-C" doesnt support TERRESTRIAL -> SEARCH NEXT ONE.
main:3220: FATAL: ***** NO USEABLE TERRESTRIAL CARD FOUND. *****
Please check wether dvb driver is loaded and
verify that no dvb application (i.e. vdr) is running.

[luk1don]

Zainstaluj kobyłę typu MythTV co ma autowyszukiwanie albo Kaffeine.
Możesz pokazać tu:

Kod: Zaznacz cały

dmesg |grep dvb

albo całe dmesg

[max95100]

instaluje mi się teraz kaffeine ale nie wiem czy czasem nie brakuje mi 2 modułów, na stronie do której podałem link w pierwszym poście piszą że musze mieć uruchomione te moduły

dvb-core
tda10021
cu1216
mantis
b2c2-flexcop-pci

a modułów b2c2-flexcop-pci i cu1216 w ogóle nie mam

w kaffeine widzi mi kartę DVB c lecz nie może mi przeszukać kanału, jest może jakaś możliwość aby ręcznie ustawić sr nadawcy??

[luk1don]

Miałeś pokazać coś...
Najlepiej na jakąś wklejkę cały:

Kod: Zaznacz cały

dmesg

Z kaffeine jaki błąd? Jakieś logi?
Ponieważ może brakować firmware (doinstalować linux-firmware-nonfree) itd.

[max95100]

pierwsze polecenie

dmesg |grep dvb

nic nie zwraca a to drugie

dmesg

zwraca mi tyle że się cały wpis w konsole nie mieści
a to co sie miści to tylko to

[ 0.238276] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[ 0.318084] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
[ 0.318166] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.318210] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.318264] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.318315] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.318371] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.318392] pci 0000:02:00.0: Boot video device
[ 0.318395] PCI: CLS 4 bytes, default 64
[ 0.319476] PCI-DMA: Disabling AGP.
[ 0.319544] PCI-DMA: aperture base @ c4000000 size 65536 KB
[ 0.319545] PCI-DMA: using GART IOMMU.
[ 0.319547] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 0.322802] LVT offset 1 assigned for vector 0x400
[ 0.322811] IBS: LVT offset 1 assigned
[ 0.322828] perf: AMD IBS detected (0x0000001f)
[ 0.322942] audit: initializing netlink socket (disabled)
[ 0.322953] type=2000 audit(1357499920.216:1): initialized
[ 0.342269] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.343652] VFS: Disk quotas dquot_6.5.2
[ 0.343688] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.344044] fuse init (API version 7.19)
[ 0.344094] msgmni has been set to 7873
[ 0.344315] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.344332] io scheduler noop registered
[ 0.344334] io scheduler deadline registered (default)
[ 0.344352] io scheduler cfq registered
[ 0.344624] pcieport 0000:00:09.0: irq 40 for MSI/MSI-X
[ 0.344698] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.344713] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.344805] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.344809] ACPI: Power Button [PWRB]
[ 0.344844] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.344846] ACPI: Power Button [PWRF]
[ 0.347088] GHES: HEST is not enabled!
[ 0.347142] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.367406] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.388206] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.388396] Linux agpgart interface v0.103
[ 0.389255] brd: module loaded
[ 0.389718] loop: module loaded
[ 0.390047] pata_acpi 0000:00:06.0: setting latency timer to 64
[ 0.390214] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
[ 0.390242] pata_acpi 0000:00:08.0: setting latency timer to 64
[ 0.390615] Fixed MDIO Bus: probed
[ 0.390642] tun: Universal TUN/TAP device driver, 1.6
[ 0.390643] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.390666] PPP generic driver version 2.4.2
[ 0.390694] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.390826] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 0.390828] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 0.390837] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 0.390859] ehci_hcd 0000:00:02.1: debug port 1
[ 0.390864] ehci_hcd 0000:00:02.1: cache line size of 4 is not supported
[ 0.390886] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfe02e000
[ 0.401850] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 0.401872] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.401873] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.401875] usb usb1: Product: EHCI Host Controller
[ 0.401877] usb usb1: Manufacturer: Linux 3.5.0-21-generic ehci_hcd
[ 0.401878] usb usb1: SerialNumber: 0000:00:02.1
[ 0.401977] hub 1-0:1.0: USB hub found
[ 0.401980] hub 1-0:1.0: 10 ports detected
[ 0.402059] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.402257] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.402259] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.402264] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 0.402287] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000
[ 0.403120] Freeing initrd memory: 14876k freed
[ 0.459587] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.459591] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.459593] usb usb2: Product: OHCI Host Controller
[ 0.459594] usb usb2: Manufacturer: Linux 3.5.0-21-generic ohci_hcd
[ 0.459595] usb usb2: SerialNumber: 0000:00:02.0
[ 0.459722] hub 2-0:1.0: USB hub found
[ 0.459726] hub 2-0:1.0: 10 ports detected
[ 0.459807] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.459863] usbcore: registered new interface driver libusual
[ 0.459888] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 0.460292] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.460297] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.460399] mousedev: PS/2 mouse device common for all mice
[ 0.460502] rtc_cmos 00:05: RTC can wake from S4
[ 0.460643] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.460680] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
[ 0.460735] device-mapper: uevent: version 1.0.3
[ 0.460779] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 0.460786] cpuidle: using governor ladder
[ 0.460787] cpuidle: using governor menu
[ 0.460789] EFI Variables Facility v0.08 2004-May-17
[ 0.460975] ashmem: initialized
[ 0.461068] TCP: cubic registered
[ 0.461145] NET: Registered protocol family 10
[ 0.461291] NET: Registered protocol family 17
[ 0.461300] Key type dns_resolver registered
[ 0.461387] PM: Hibernation image not present or could not be loaded.
[ 0.461398] registered taskstats version 1
[ 0.463261] Key type trusted registered
[ 0.464565] Key type encrypted registered
[ 0.466056] Magic number: 13:704:343
[ 0.466081] tty tty60: hash matches
[ 0.466157] rtc_cmos 00:05: setting system clock to 2013-01-06 19:18:41 UTC (1357499921)
[ 0.466203] powernow-k8: Found 1 AMD Phenom(tm) II X2 550 Processor (2 cpu cores) (version 2.20.00)
[ 0.466231] powernow-k8: 0 : pstate 0 (3100 MHz)
[ 0.466233] powernow-k8: 1 : pstate 1 (2400 MHz)
[ 0.466234] powernow-k8: 2 : pstate 2 (1900 MHz)
[ 0.466234] powernow-k8: 3 : pstate 3 (800 MHz)
[ 0.466356] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.466357] EDD information not available.
[ 0.467343] Freeing unused kernel memory: 932k freed
[ 0.467601] Write protecting the kernel read-only data: 12288k
[ 0.470944] Freeing unused kernel memory: 1464k freed
[ 0.473843] Freeing unused kernel memory: 1120k freed
[ 0.486133] udevd[88]: starting version 175
[ 0.523057] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 0.523212] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
[ 0.523232] forcedeth 0000:00:07.0: setting latency timer to 64
[ 0.712944] usb 1-3: new high-speed USB device number 2 using ehci_hcd
[ 0.845023] usb 1-3: New USB device found, idVendor=0424, idProduct=2514
[ 0.845027] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 0.845168] hub 1-3:1.0: USB hub found
[ 0.845267] hub 1-3:1.0: 4 ports detected
[ 1.012197] usb 1-6: new high-speed USB device number 4 using ehci_hcd
[ 1.044664] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:d0:32:47:88
[ 1.044669] forcedeth 0000:00:07.0: highdma pwrctl mgmt lnktim msi desc-v3
[ 1.044703] sata_nv 0000:00:08.0: version 3.5
[ 1.044758] sata_nv 0000:00:08.0: setting latency timer to 64
[ 1.044987] scsi0 : sata_nv
[ 1.045050] scsi1 : sata_nv
[ 1.045143] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 21
[ 1.045145] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 21
[ 1.045186] pata_amd 0000:00:06.0: version 0.4.1
[ 1.045208] pata_amd 0000:00:06.0: setting latency timer to 64
[ 1.045424] scsi2 : pata_amd
[ 1.045471] scsi3 : pata_amd
[ 1.045734] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 1.045735] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 1.148035] usb 1-6: New USB device found, idVendor=0951, idProduct=1653
[ 1.148038] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.148040] usb 1-6: Product: DT 100 G2
[ 1.148042] usb 1-6: Manufacturer: Kingston
[ 1.148043] usb 1-6: SerialNumber: 0014780F995FBAA1C56800FC
[ 1.149506] usbcore: registered new interface driver uas
[ 1.149688] Initializing USB Mass Storage driver...
[ 1.149765] scsi4 : usb-storage 1-6:1.0
[ 1.149816] usbcore: registered new interface driver usb-storage
[ 1.149817] USB Mass Storage support registered.
[ 1.259579] usb 1-7: new high-speed USB device number 5 using ehci_hcd
[ 1.264006] ata3.00: HPA detected: current 156293231, native 156301488
[ 1.264010] ata3.00: ATA-6: ST380012A, 4.04, max UDMA/100
[ 1.264012] ata3.00: 156293231 sectors, multi 16: LBA48
[ 1.264017] ata3: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1.279912] ata3.00: configured for UDMA/100
[ 1.319438] Refined TSC clocksource calibration: 3114.162 MHz.
[ 1.319442] Switching to clocksource tsc
[ 1.394268] usb 1-7: New USB device found, idVendor=090c, idProduct=6300
[ 1.394270] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.394272] usb 1-7: Product: USB2.0 Card Reader
[ 1.394273] usb 1-7: Manufacturer: SMI
[ 1.394275] usb 1-7: SerialNumber: 12345678901234567890
[ 1.394620] scsi5 : usb-storage 1-7:1.0
[ 1.510956] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.541406] ata1.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
[ 1.541409] ata1.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.547687] ata1.00: configured for UDMA/133
[ 1.547811] scsi 0:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
[ 1.547910] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 1.547922] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.547937] sd 0:0:0:0: [sda] Write Protect is off
[ 1.547940] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.547951] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.559663] sda: sda1 sda2 sda3
[ 1.559918] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.822168] usb 2-4: new low-speed USB device number 2 using ohci_hcd
[ 2.013700] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.021782] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-H62N, CL00, max UDMA/100
[ 2.034668] usb 2-4: New USB device found, idVendor=0bc7, idProduct=0006
[ 2.034671] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.034673] usb 2-4: Product: USB Receiver
[ 2.034674] usb 2-4: Manufacturer: X10 Wireless Technology Inc
[ 2.037737] ata2.00: configured for UDMA/100
[ 2.043010] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0 ANSI: 5
[ 2.048100] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.048103] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.048191] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.048234] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.048324] scsi 2:0:0:0: Direct-Access ATA ST380012A 4.04 PQ: 0 ANSI: 5
[ 2.048401] sd 2:0:0:0: [sdb] 156293231 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.048431] sd 2:0:0:0: [sdb] Write Protect is off
[ 2.048433] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.048444] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.048540] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2.048653] ata4: port disabled--ignoring
[ 2.072551] sdb: sdb1 sdb2 sdb3
[ 2.072794] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 2.109488] usb 1-3.1: new full-speed USB device number 6 using ehci_hcd
[ 2.146538] scsi 4:0:0:0: Direct-Access Kingston DT 100 G2 PMAP PQ: 0 ANSI: 0 CCS
[ 2.147026] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 2.148402] sd 4:0:0:0: [sdc] 7835648 512-byte logical blocks: (4.01 GB/3.73 GiB)
[ 2.150396] sd 4:0:0:0: [sdc] Write Protect is off
[ 2.150400] sd 4:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 2.152391] sd 4:0:0:0: [sdc] No Caching mode page present
[ 2.152394] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.158503] sd 4:0:0:0: [sdc] No Caching mode page present
[ 2.158506] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.159506] sdc: sdc1 sdc2
[ 2.165235] sd 4:0:0:0: [sdc] No Caching mode page present
[ 2.165238] sd 4:0:0:0: [sdc] Assuming drive cache: write through
[ 2.165239] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 2.204242] usb 1-3.1: New USB device found, idVendor=046d, idProduct=c52e
[ 2.204245] usb 1-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.204247] usb 1-3.1: Product: USB Receiver
[ 2.204249] usb 1-3.1: Manufacturer: Logitech
[ 2.210297] usbcore: registered new interface driver usbhid
[ 2.210299] usbhid: USB HID core driver
[ 2.211746] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-3/1-3.1/1-3.1:1.0/input/input2
[ 2.211824] hid-generic 0003:046D:C52E.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:02.1-3.1/input0
[ 2.212375] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:02.1/usb1/1-3/1-3.1/1-3.1:1.1/input/input3
[ 2.212508] hid-generic 0003:046D:C52E.0002: input,hiddev0,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:02.1-3.1/input1
[ 2.404872] usb 1-3.3: new high-speed USB device number 7 using ehci_hcd
[ 2.803749] usb 1-3.3: New USB device found, idVendor=0ac8, idProduct=c31d
[ 2.803752] usb 1-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.803754] usb 1-3.3: Product: NMG 3M Webcam
[ 2.803756] usb 1-3.3: Manufacturer: Vimicro Corp.
[ 2.891533] usb 1-3.4: new full-speed USB device number 8 using ehci_hcd
[ 2.988406] usb 1-3.4: New USB device found, idVendor=4c2d, idProduct=2900
[ 2.988409] usb 1-3.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.988411] usb 1-3.4: Product: Samsung UC Audio
[ 2.988413] usb 1-3.4: Manufacturer: UCQ01000
[ 2.989698] input: UCQ01000 Samsung UC Audio as /devices/pci0000:00/0000:00:02.1/usb1/1-3/1-3.4/1-3.4:1.3/input/input4
[ 2.989754] hid-generic 0003:4C2D:2900.0003: input,hidraw2: USB HID v1.00 Device [UCQ01000 Samsung UC Audio] on usb-0000:00:02.1-3.4/input3
[ 3.566363] scsi 5:0:0:0: Direct-Access SMI Reader 1.00 PQ: 0 ANSI: 0 CCS
[ 3.566850] sd 5:0:0:0: Attached scsi generic sg4 type 0
[ 3.568223] sd 5:0:0:0: [sdd] Attached SCSI removable disk
[ 5.207940] EXT4-fs (sdb2): INFO: recovery required on readonly filesystem
[ 5.207942] EXT4-fs (sdb2): write access will be enabled during recovery
[ 5.378628] EXT4-fs (sdb2): recovery complete
[ 5.386591] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 21.584432] Adding 4738044k swap on /dev/sdb1. Priority:-1 extents:1 across:4738044k
[ 21.589317] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.635373] udevd[380]: starting version 175
[ 21.679497] lp: driver loaded but no devices found
[ 21.680544] i2c i2c-0: nForce2 SMBus adapter at 0x1c00
[ 21.680563] i2c i2c-1: nForce2 SMBus adapter at 0x1c40
[ 21.699116] Linux video capture interface: v2.00
[ 21.716163] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 21.724495] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 21.730505] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 21.732651] uvcvideo: Found UVC 1.00 device NMG 3M Webcam (0ac8:c31d)
[ 21.770853] wmi: Mapper loaded
[ 21.786619] [drm] Initialized drm 1.1.0 20060810
[ 21.787394] input: NMG 3M Webcam as /devices/pci0000:00/0000:00:02.1/usb1/1-3/1-3.3/1-3.3:1.0/input/input5
[ 21.787465] usbcore: registered new interface driver uvcvideo
[ 21.787467] USB Video Class driver (1.1.1)
[ 21.788924] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 21.789948] DVB: registering new adapter (Mantis DVB adapter)
[ 21.793789] MCE: In-kernel MCE decoding enabled.
[ 21.799242] EDAC MC: Ver: 2.1.0
[ 21.800325] k10temp 0000:00:18.3: unreliable CPU thermal sensor; monitoring disabled
[ 21.802022] AMD64 EDAC driver v3.4.0
[ 21.802043] EDAC amd64: DRAM ECC disabled.
[ 21.802047] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 21.802047] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 21.802047] (Note that use of the override may cause unknown side effects.)
[ 21.810110] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[ 21.819992] type=1400 audit(1357496342.902:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=469 comm="apparmor_parser"
[ 21.820384] type=1400 audit(1357496342.906:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=469 comm="apparmor_parser"
[ 21.820578] type=1400 audit(1357496342.906:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=469 comm="apparmor_parser"
[ 21.822368] type=1400 audit(1357496342.906:5): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=601 comm="apparmor_parser"
[ 21.841343] parport_pc 00:09: reported by Plug and Play ACPI
[ 21.841389] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 21.843990] ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16
[ 21.844343] [drm] nouveau 0000:02:00.0: Detected an NV50 generation card (0x094100a1)
[ 21.845874] [drm] nouveau 0000:02:00.0: Checking PRAMIN for VBIOS
[ 21.874691] microcode: CPU0: patch_level=0x01000086
[ 21.896997] [drm] nouveau 0000:02:00.0: ... appears to be valid
[ 21.896999] [drm] nouveau 0000:02:00.0: Using VBIOS from PRAMIN
[ 21.897001] [drm] nouveau 0000:02:00.0: BIT BIOS found
[ 21.897003] [drm] nouveau 0000:02:00.0: Bios version 62.94.3c.00
[ 21.897005] [drm] nouveau 0000:02:00.0: TMDS table version 2.0
[ 21.897896] [drm] nouveau 0000:02:00.0: MXM: no VBIOS data, nothing to do
[ 21.897898] [drm] nouveau 0000:02:00.0: DCB version 4.0
[ 21.897900] [drm] nouveau 0000:02:00.0: DCB outp 00: 02000300 00000028
[ 21.897902] [drm] nouveau 0000:02:00.0: DCB outp 01: 01000302 00020030
[ 21.897903] [drm] nouveau 0000:02:00.0: DCB outp 02: 04011310 00000028
[ 21.897904] [drm] nouveau 0000:02:00.0: DCB outp 03: 02022332 00020030
[ 21.897905] [drm] nouveau 0000:02:00.0: DCB conn 00: 00001030
[ 21.897907] [drm] nouveau 0000:02:00.0: DCB conn 01: 00000100
[ 21.897908] [drm] nouveau 0000:02:00.0: DCB conn 02: 00002261
[ 21.897911] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table 0 at offset 0xD0D1
[ 21.902278] Registered IR keymap rc-medion-x10-digitainer
[ 21.902581] input: X10 Wireless Technology Inc USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/rc/rc0/input6
[ 21.902701] rc0: X10 Wireless Technology Inc USB Receiver as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/rc/rc0
[ 21.902812] input: X10 Wireless Technology Inc USB Receiver mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input7
[ 21.903057] usbcore: registered new interface driver ati_remote
[ 21.922951] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table 1 at offset 0xD4C2
[ 21.925769] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table 2 at offset 0xE48B
[ 21.925775] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table 3 at offset 0xE5D4
[ 21.926841] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table 4 at offset 0xE83C
[ 21.926842] [drm] nouveau 0000:02:00.0: Parsing VBIOS init table at offset 0xE8A1
[ 21.946637] [drm] nouveau 0000:02:00.0: 0xE8A1: Condition still not met after 20ms, skipping following opcodes
[ 21.952134] lp0: using parport0 (interrupt-driven).
[ 21.956041] [TTM] Zone kernel: Available graphics memory: 2024916 kiB
[ 21.956043] [TTM] Initializing pool allocator
[ 21.956047] [TTM] Initializing DMA pool allocator
[ 21.956058] [drm] nouveau 0000:02:00.0: Detected 512MiB VRAM (GDDR3)
[ 21.958534] [drm] nouveau 0000:02:00.0: 512 MiB GART (aperture)
[ 21.968598] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 21.968600] [drm] No driver support for vblank timestamp query.
[ 21.972803] kvm: Nested Virtualization enabled
[ 21.972805] kvm: Nested Paging enabled
[ 21.974429] [drm] nouveau 0000:02:00.0: 1 available performance level(s)
[ 21.974433] [drm] nouveau 0000:02:00.0: 3: core 700MHz shader 1800MHz memory 900MHz voltage 1100mV fanspeed 100%
[ 21.974436] [drm] nouveau 0000:02:00.0: c: core 500MHz shader 1250MHz memory 499MHz voltage 1000mV fanspeed 100%
[ 21.982373] [drm] nouveau 0000:02:00.0: MM: using CRYPT for buffer copies
[ 22.085700] [drm] nouveau 0000:02:00.0: allocated 1680x1050 fb: 0x2c0000, bo ffff880113596800
[ 22.085804] fbcon: nouveaufb (fb0) is primary device
[ 22.105886] Console: switching to colour frame buffer device 210x65
[ 22.107566] fb0: nouveaufb frame buffer device
[ 22.107566] drm: registered panic notifier
[ 22.107575] [drm] Initialized nouveau 1.0.0 20120316 for 0000:02:00.0 on minor 0
[ 22.109214] usbcore: registered new interface driver snd-usb-audio
[ 22.150513] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 22.150518] hda_intel: Disabling MSI
[ 22.150541] snd_hda_intel 0000:00:05.0: setting latency timer to 64
[ 22.176210] ppdev: user-space parallel port driver
[ 22.441113] microcode: failed to load file amd-ucode/microcode_amd.bin
[ 22.441138] microcode: CPU1: patch_level=0x01000086
[ 22.442262] microcode: failed to load file amd-ucode/microcode_amd.bin
[ 22.442311] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 22.704735] DVB: registering adapter 0 frontend 0 (Philips TDA10023 DVB-C)...
[ 22.706734] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 22.706741] saa7134[0]: found at 0000:01:06.0, rev: 1, irq: 16, latency: 32, mmio: 0xfdeff000
[ 22.706746] saa7134[0]: subsystem: 1894:a006, board: KNC One TV-Station DVR [card=24,autodetected]
[ 22.706772] saa7134[0]: board init: gpio is 830000
[ 22.857548] saa7134[0]: i2c eeprom 00: 94 18 06 a0 06 80 00 01 00 00 00 00 00 00 01 00
[ 22.857554] saa7134[0]: i2c eeprom 10: 00 ff 86 0e ff 20 ff ff ff ff ff ff ff ff ff ff
[ 22.857559] saa7134[0]: i2c eeprom 20: 01 40 01 02 02 03 01 03 06 ff 01 df ff ff ff ff
[ 22.857564] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857568] saa7134[0]: i2c eeprom 40: ff 05 00 c0 86 ff ff ff ff ff ff ff ff ff ff ff
[ 22.857572] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857577] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857581] saa7134[0]: i2c eeprom 70: 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857586] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857590] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857595] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857599] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857604] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857608] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857612] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.857617] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 22.874382] tda9887 13-0043: creating new instance
[ 22.874384] tda9887 13-0043: tda988[5/6/7] found
[ 22.881496] tuner 13-0043: Tuner 74 found with type(s) Radio TV.
[ 22.897457] Chip ID is not zero. It is not a TEA5767
[ 22.897463] tuner 13-0060: Tuner -1 found with type(s) Radio TV.
[ 22.905440] tuner-simple 13-0060: creating new instance
[ 22.905442] tuner-simple 13-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[ 22.978281] saa6752hs 13-0020: chip found @ 0x40 (saa7134[0])
[ 23.001252] saa7134[0]: registered device video1 [v4l2]
[ 23.001282] saa7134[0]: registered device vbi0
[ 23.001306] saa7134[0]: registered device radio0
[ 23.002699] saa7134 ALSA driver for DMA sound loaded
[ 23.002721] saa7134[0]/alsa: saa7134[0] at 0xfdeff000 irq 16 registered as card -2
[ 23.004508] saa7134[0]: registered device video2 [mpeg]
[ 24.302009] input: HDA NVidia Line as /devices/pci0000:00/0000:00:05.0/sound/card0/input8
[ 24.302079] input: HDA NVidia Front Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input9
[ 24.302133] input: HDA NVidia Rear Mic as /devices/pci0000:00/0000:00:05.0/sound/card0/input10
[ 24.302187] input: HDA NVidia Front Headphone as /devices/pci0000:00/0000:00:05.0/sound/card0/input11
[ 24.302246] input: HDA NVidia Line Out Side as /devices/pci0000:00/0000:00:05.0/sound/card0/input12
[ 24.302298] input: HDA NVidia Line Out CLFE as /devices/pci0000:00/0000:00:05.0/sound/card0/input13
[ 24.302349] input: HDA NVidia Line Out Surround as /devices/pci0000:00/0000:00:05.0/sound/card0/input14
[ 24.302401] input: HDA NVidia Line Out Front as /devices/pci0000:00/0000:00:05.0/sound/card0/input15
[ 24.890427] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro
[ 26.375936] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
[ 29.222150] init: failsafe main process (1028) killed by TERM signal
[ 29.293007] Bluetooth: Core ver 2.16
[ 29.293028] NET: Registered protocol family 31
[ 29.293029] Bluetooth: HCI device and connection manager initialized
[ 29.293515] Bluetooth: HCI socket layer initialized
[ 29.293518] Bluetooth: L2CAP socket layer initialized
[ 29.293522] Bluetooth: SCO socket layer initialized
[ 29.302906] type=1400 audit(1357496350.406:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1170 comm="apparmor_parser"
[ 29.303426] type=1400 audit(1357496350.406:7): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1170 comm="apparmor_parser"
[ 29.315856] type=1400 audit(1357496350.418:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1192 comm="apparmor_parser"
[ 29.316159] type=1400 audit(1357496350.418:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper//chromium_browser" pid=1192 comm="apparmor_parser"
[ 29.319227] type=1400 audit(1357496350.422:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-freerdp/freerdp-session-wrapper" pid=1193 comm="apparmor_parser"
[ 29.319528] type=1400 audit(1357496350.422:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-freerdp/freerdp-session-wrapper//chromium_browser" pid=1193 comm="apparmor_parser"
[ 29.319889] Bluetooth: RFCOMM TTY layer initialized
[ 29.319892] Bluetooth: RFCOMM socket layer initialized
[ 29.319893] Bluetooth: RFCOMM ver 1.11
[ 29.328163] type=1400 audit(1357496350.430:12): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-uccsconfigure/uccsconfigure-session-wrapper" pid=1205 comm="apparmor_parser"
[ 29.328468] type=1400 audit(1357496350.430:13): apparmor="STATUS" operation="profile_load" name="/usr/lib/x86_64-linux-gnu/lightdm-remote-session-uccsconfigure/uccsconfigure-session-wrapper//chromium_browser" pid=1205 comm="apparmor_parser"
[ 29.331844] type=1400 audit(1357496350.434:14): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1206 comm="apparmor_parser"
[ 29.332217] type=1400 audit(1357496350.434:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1206 comm="apparmor_parser"
[ 29.339584] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 29.339587] Bluetooth: BNEP filters: protocol multicast
[ 29.366677] forcedeth 0000:00:07.0: irq 41 for MSI/MSI-X
[ 29.366703] forcedeth 0000:00:07.0: eth0: MSI enabled
[ 34.395123] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 34.410708] ISO 9660 Extensions: RRIP_1991A

Początkowo kaffeine wykrywał mi prawidłowo źródło sygnału (kabel) lecz podczas przeszukiwania nie widział tunera, teraz (nie wiem co zrobiłem) ale mi przeszukuje tuner jednak nie mogę nigdzie wprowadzić ustawień nadawcy i z tego powodu nic mi nie znajduje.

[luk1don]

Ustawienia Kaffeine? Poszukaj w necie, bo nie używam, może /home/<user>/.kde4/share/apps/kaffeine/ i inne.
Doinstaluj firmware w razie czego jak pisałem.