Witam
Bardzo was proszę o pomoc w uruchomieniu klawiatury Logitech g13 na ubuntu posiadam wersje 15.10. Siedze juz nad tym 3 dzień i nic.
Postępuje według tej instukcji :
# Userspace driver for the G13
## Installation
Make sure you have boost and libusb-1.0 installed.
### For Ubuntu (15.10)
* ***sudo apt-get install libusb-1.0-0-dev***
* ***sudo apt-get install libboost-all-dev***
### Build
Compile by running
make
If you want to run the daemon as user, put the file 91-g13.rules into /etc/udev/rules.d/ (or whatever directory your distribution uses).
## Running
Connect your device, then run ./g13d, it should automatically find your device.
i dalej nic
za pomocą terminala sciągłem to:
* ***sudo apt-get install libusb-1.0-0-dev***
* ***sudo apt-get install libboost-all-dev***
Przekopiowałem ten plik 91-g13.rules do /etc/udev/rules.d/
uruchamiam terminal wpisuje ./g13d
i dalej nic nie wiem co robię zle. Nie znam sie bardzo na ubuntu ale i nie wiem co robie zle
ogladalem ten filmik z 100 razy https://www.youtube.com/watch?v=Xk3TVAs80ZM idalej klawiatura nie reaguje.
Proszę bardzo o pomoc.
Logitech g13 - jak uruchomić?
-
Arkosake
- Serdeczny Borsuk
- Posty: 175
- Rejestracja: 07 lut 2009, 16:38
- Płeć: Mężczyzna
- Wersja Ubuntu: inny OS
- Środowisko graficzne: KDE Plasma
- Architektura: x86_64
- Lokalizacja: Gdańsk
Re: Logitech g13 - jak uruchomić?
Dobrze, a czy dokonałeś instalacji samego sterownika tak jak jest na tym filmie, bo z twojego opisu wynika że nie? W filmie w 4:30 masz budowanie sterownika z plików źródłowych. Z resztą w instrukcji masz : ### Buildbartezo pisze: za pomocą terminala sciągłem to:
* ***sudo apt-get install libusb-1.0-0-dev***
* ***sudo apt-get install libboost-all-dev***
Przekopiowałem ten plik 91-g13.rules do /etc/udev/rules.d/
uruchamiam terminal wpisuje ./g13d
i dalej nic nie wiem co robię zle. Nie znam sie bardzo na ubuntu ale i nie wiem co robie zle
ogladalem ten filmik z 100 razy https://www.youtube.com/watch?v=Xk3TVAs80ZM idalej klawiatura nie reaguje.
Proszę bardzo o pomoc.
Compile by running "make", gdzie polecenie "make" wydajesz w terminalu po wcześniejszym wejściu do folderu za pomocą polecenia "cd"
Re: Logitech g13 - jak uruchomić?
tylko że u mnie wyskakuje jakiś bład:
oraz mam różnice z filmem w 3:44 minucie u mnie w terminalu wyskakuje tak :
nie ogarniam Ubuntu a zalezy mi na uruchomienu tego Logitecha.
Pobrałem z tej strony https://github.com/ecraven/g13 paczkę plików g13-master.
wpisuję w terminal
i dalej nic. Po 3 dniach jestem dalej w tym miejscu.
Kod: Zaznacz cały
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ cd Pobrane
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane$ cd g13
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ dir
default-keymap g13.c logo.h Makefile
dvorak-keymap hello.pbm logo.pbm pbm2lpbm.c
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ make
make -C /lib/modules/4.2.0-16-generic/build SUBDIRS=/home/bartek/Pobrane/g13 modules
make[1]: Entering directory '/usr/src/linux-headers-4.2.0-16-generic'
CC [M] /home/bartek/Pobrane/g13/g13.o
/home/bartek/Pobrane/g13/g13.c: In function ‘g13_disconnect’:
/home/bartek/Pobrane/g13/g13.c:170:3: error: implicit declaration of function ‘usb_buffer_free’ [-Werror=implicit-function-declaration]
usb_buffer_free(interface_to_usbdev(interface), KEY_BUFFER_SIZE, urb->transfe
^
/home/bartek/Pobrane/g13/g13.c:173:5: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
kfree(lcd_buffer);
^
In file included from include/linux/thread_info.h:11:0,
from ./arch/x86/include/asm/preempt.h:6,
from include/linux/preempt.h:64,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:35,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from /home/bartek/Pobrane/g13/g13.c:16:
/home/bartek/Pobrane/g13/g13.c: At top level:
include/linux/bug.h:33:45: error: negative width in bit-field ‘<anonymous>’
#define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:-!!(e); }))
^
include/linux/kernel.h:829:3: note: in expansion of macro ‘BUILD_BUG_ON_ZERO’
BUILD_BUG_ON_ZERO((perms) & 2) + \
^
include/linux/sysfs.h:92:12: note: in expansion of macro ‘VERIFY_OCTAL_PERMISSIONS’
.mode = VERIFY_OCTAL_PERMISSIONS(_mode) }, \
^
/home/bartek/Pobrane/g13/g13.c:233:9: note: in expansion of macro ‘__ATTR’
__ATTR(m_leds, 0666, m_show, m_store);
^
include/linux/bug.h:33:45: error: negative width in bit-field ‘<anonymous>’
#define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:-!!(e); }))
^
include/linux/kernel.h:829:3: note: in expansion of macro ‘BUILD_BUG_ON_ZERO’
BUILD_BUG_ON_ZERO((perms) & 2) + \
^
include/linux/sysfs.h:92:12: note: in expansion of macro ‘VERIFY_OCTAL_PERMISSIONS’
.mode = VERIFY_OCTAL_PERMISSIONS(_mode) }, \
^
/home/bartek/Pobrane/g13/g13.c:268:9: note: in expansion of macro ‘__ATTR’
__ATTR(keymap, 0666, keymap_show, keymap_store);
^
/home/bartek/Pobrane/g13/g13.c: In function ‘set_lcd’:
/home/bartek/Pobrane/g13/g13.c:294:18: error: implicit declaration of function ‘kmalloc’ [-Werror=implicit-function-declaration]
lcd_buffer = kmalloc(LCD_BUFFER_SIZE + 32, GFP_KERNEL);
^
/home/bartek/Pobrane/g13/g13.c:294:16: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
lcd_buffer = kmalloc(LCD_BUFFER_SIZE + 32, GFP_KERNEL);
^
/home/bartek/Pobrane/g13/g13.c: At top level:
/home/bartek/Pobrane/g13/g13.c:323:11: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.read = lcd_read,
^
/home/bartek/Pobrane/g13/g13.c:323:11: note: (near initialization for ‘lcd_attribute.read’)
/home/bartek/Pobrane/g13/g13.c:324:12: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.write = lcd_write,
^
/home/bartek/Pobrane/g13/g13.c:324:12: note: (near initialization for ‘lcd_attribute.write’)
In file included from include/linux/thread_info.h:11:0,
from ./arch/x86/include/asm/preempt.h:6,
from include/linux/preempt.h:64,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:35,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from /home/bartek/Pobrane/g13/g13.c:16:
include/linux/bug.h:33:45: error: negative width in bit-field ‘<anonymous>’
#define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:-!!(e); }))
^
include/linux/kernel.h:829:3: note: in expansion of macro ‘BUILD_BUG_ON_ZERO’
BUILD_BUG_ON_ZERO((perms) & 2) + \
^
include/linux/sysfs.h:92:12: note: in expansion of macro ‘VERIFY_OCTAL_PERMISSIONS’
.mode = VERIFY_OCTAL_PERMISSIONS(_mode) }, \
^
/home/bartek/Pobrane/g13/g13.c:364:9: note: in expansion of macro ‘__ATTR’
__ATTR(rgb, 0666, rgb_show, rgb_store);
^
/home/bartek/Pobrane/g13/g13.c: In function ‘g13_probe’:
/home/bartek/Pobrane/g13/g13.c:423:9: error: implicit declaration of function ‘usb_buffer_alloc’ [-Werror=implicit-function-declaration]
buf = usb_buffer_alloc(dev, KEY_BUFFER_SIZE, GFP_KERNEL, &new_dma);
^
/home/bartek/Pobrane/g13/g13.c:423:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
buf = usb_buffer_alloc(dev, KEY_BUFFER_SIZE, GFP_KERNEL, &new_dma);
^
cc1: some warnings being treated as errors
scripts/Makefile.build:264: recipe for target '/home/bartek/Pobrane/g13/g13.o' failed
make[2]: *** [/home/bartek/Pobrane/g13/g13.o] Error 1
Makefile:1398: recipe for target '_module_/home/bartek/Pobrane/g13' failed
make[1]: *** [_module_/home/bartek/Pobrane/g13] Error 2
make[1]: Leaving directory '/usr/src/linux-headers-4.2.0-16-generic'
Makefile:7: recipe for target 'all' failed
make: *** [all] Error 2
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$
Kod: Zaznacz cały
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ chmod 777 /dev/uinput
chmod: changing permissions of ‘/dev/uinput’: Operation not permitted
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ Pobrałem z tej strony https://github.com/ecraven/g13 paczkę plików g13-master.
wpisuję w terminal
Kod: Zaznacz cały
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ cd Pobrane/
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane$ cd g13/
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ dir
91-g13.rules g13_keys.cc g13.svg logo.h starcraft2.bind
clock.sh g13_lcd.cc g13_test.py logo.lpbm starcraft.lpbm
eve-online.bind g13_log.cc hello.lpbm Makefile war.bind
g13.cc g13_main.cc helper.cpp pbm2lpbm.c
g13_fonts.cc g13.png helper.hpp README.md
g13.h g13_stick.cc hon.bind spring.bind
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ make
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_main.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_log.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_fonts.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_lcd.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_stick.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c g13_keys.cc
g++ -DBOOST_LOG_DYN_LINK -std=c++0x -c helper.cpp
g++ -o g13d -std=c++0x \
g13_main.o g13.o g13_log.o g13_fonts.o g13_lcd.o g13_stick.o g13_keys.o helper.o \
-lusb-1.0 -lboost_program_options \
-lboost_log \
-lboost_system -lpthread
g++ -o pbm2lpbm pbm2lpbm.c
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ ./g13
bash: ./g13: No such file or directory
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$
Re: Logitech g13 - jak uruchomić?
udało mi sie uruchomic tego logitecha komunikuje sie z ubuntu
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ ./g13d
bash: ./g13d: No such file or directory
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ cd Pobrane
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane$ cd g13
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ ./g13d
[2016-11-27 01:46:06.334984] [0xb7158700] [info] set log level to info
[2016-11-27 01:46:06.335599] [0xb7158700] [info] Known keys on G13:
[2016-11-27 01:46:06.335658] [0xb7158700] [info] BD DOWN G1 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G2 G20 G21 G22 G3 G4 G5 G6 G7 G8 G9 L1 L2 L3 L4 LEFT LIGHT LIGHT2 LIGHT_STATE M1 M2 M3 MISC_TOGGLE MR TOP UNDEF1 UNDEF3
[2016-11-27 01:46:06.335688] [0xb7158700] [info] Known keys to map to:
[2016-11-27 01:46:06.335746] [0xb7158700] [info] 0 1 2 3 4 5 6 7 8 9 A APOSTROPHE B BACKSLASH BACKSPACE C CAPSLOCK COMMA D DELETE DOT DOWN E END ENTER EQUAL ESC F F1 F10 F11 F12 F2 F3 F4 F5 F6 F7 F8 F9 G GRAVE H HOME I INSERT J K KP0 KP1 KP2 KP3 KP4 KP5 KP6 KP7 KP8 KP9 KPASTERISK KPDOT KPMINUS KPPLUS L LEFT LEFTALT LEFTBRACE LEFTCTRL LEFTSHIFT M MINUS N NUMLOCK O P PAGEDOWN PAGEUP Q R RIGHT RIGHTALT RIGHTBRACE RIGHTCTRL RIGHTSHIFT S SCROLLLOCK SEMICOLON SLASH SPACE T TAB U UP V W X Y Z
[2016-11-27 01:46:06.344802] [0xb7158700] [info] Found 1 G13s
[2016-11-27 01:46:06.374225] [0xb7158700] [error] /dev/uinput doesn't grant write permissions
[2016-11-27 01:46:06.374432] [0xb7158700] [info] Active Stick zones
STICK_UP { 0 x 0.1 / 1 x 0.3 } SEND KEYS: UP
STICK_DOWN { 0 x 0.7 / 1 x 0.9 } SEND KEYS: DOWN
STICK_LEFT { 0 x 0 / 0.2 x 1 } SEND KEYS: LEFT
STICK_RIGHT { 0.8 x 0 / 1 x 1 } SEND KEYS: RIGHT
STICK_PAGEUP { 0 x 0 / 1 x 0.1 } SEND KEYS: PAGEUP
STICK_PAGEDOWN { 0 x 0.9 / 1 x 1 } SEND KEYS: PAGEDOWN
} SEND KEYS: UP
STICK_DOWN { 0 x 0.7 / 1 x 0.9 } SEND KEYS: DOWN
STICK_LEFT { 0 x 0 / 0.2 x 1 } SEND KEYS: LEFT
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ ./g13d
bash: ./g13d: No such file or directory
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~$ cd Pobrane
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane$ cd g13
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ ./g13d
[2016-11-27 01:46:06.334984] [0xb7158700] [info] set log level to info
[2016-11-27 01:46:06.335599] [0xb7158700] [info] Known keys on G13:
[2016-11-27 01:46:06.335658] [0xb7158700] [info] BD DOWN G1 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G2 G20 G21 G22 G3 G4 G5 G6 G7 G8 G9 L1 L2 L3 L4 LEFT LIGHT LIGHT2 LIGHT_STATE M1 M2 M3 MISC_TOGGLE MR TOP UNDEF1 UNDEF3
[2016-11-27 01:46:06.335688] [0xb7158700] [info] Known keys to map to:
[2016-11-27 01:46:06.335746] [0xb7158700] [info] 0 1 2 3 4 5 6 7 8 9 A APOSTROPHE B BACKSLASH BACKSPACE C CAPSLOCK COMMA D DELETE DOT DOWN E END ENTER EQUAL ESC F F1 F10 F11 F12 F2 F3 F4 F5 F6 F7 F8 F9 G GRAVE H HOME I INSERT J K KP0 KP1 KP2 KP3 KP4 KP5 KP6 KP7 KP8 KP9 KPASTERISK KPDOT KPMINUS KPPLUS L LEFT LEFTALT LEFTBRACE LEFTCTRL LEFTSHIFT M MINUS N NUMLOCK O P PAGEDOWN PAGEUP Q R RIGHT RIGHTALT RIGHTBRACE RIGHTCTRL RIGHTSHIFT S SCROLLLOCK SEMICOLON SLASH SPACE T TAB U UP V W X Y Z
[2016-11-27 01:46:06.344802] [0xb7158700] [info] Found 1 G13s
[2016-11-27 01:46:06.374225] [0xb7158700] [error] /dev/uinput doesn't grant write permissions
[2016-11-27 01:46:06.374432] [0xb7158700] [info] Active Stick zones
STICK_UP { 0 x 0.1 / 1 x 0.3 } SEND KEYS: UP
STICK_DOWN { 0 x 0.7 / 1 x 0.9 } SEND KEYS: DOWN
STICK_LEFT { 0 x 0 / 0.2 x 1 } SEND KEYS: LEFT
STICK_RIGHT { 0.8 x 0 / 1 x 1 } SEND KEYS: RIGHT
STICK_PAGEUP { 0 x 0 / 1 x 0.1 } SEND KEYS: PAGEUP
STICK_PAGEDOWN { 0 x 0.9 / 1 x 1 } SEND KEYS: PAGEDOWN
} SEND KEYS: UP
STICK_DOWN { 0 x 0.7 / 1 x 0.9 } SEND KEYS: DOWN
STICK_LEFT { 0 x 0 / 0.2 x 1 } SEND KEYS: LEFT
Re: Logitech g13 - jak uruchomić?
Mam nowy problem terminal wykazuje bład:
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ ./g13d
[2016-11-27 16:11:53.563565] [0xb71f3d80] [info] set log level to info
[2016-11-27 16:11:53.564238] [0xb71f3d80] [info] Known keys on G13:
[2016-11-27 16:11:53.564352] [0xb71f3d80] [info] BD DOWN G1 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G2 G20 G21 G22 G3 G4 G5 G6 G7 G8 G9 L1 L2 L3 L4 LEFT LIGHT LIGHT2 LIGHT_STATE M1 M2 M3 MISC_TOGGLE MR TOP UNDEF1 UNDEF3
[2016-11-27 16:11:53.564420] [0xb71f3d80] [info] Known keys to map to:
[2016-11-27 16:11:53.564530] [0xb71f3d80] [info] 0 1 2 3 4 5 6 7 8 9 A APOSTROPHE B BACKSLASH BACKSPACE C CAPSLOCK COMMA D DELETE DOT DOWN E END ENTER EQUAL ESC F F1 F10 F11 F12 F2 F3 F4 F5 F6 F7 F8 F9 G GRAVE H HOME I INSERT J K KP0 KP1 KP2 KP3 KP4 KP5 KP6 KP7 KP8 KP9 KPASTERISK KPDOT KPMINUS KPPLUS L LEFT LEFTALT LEFTBRACE LEFTCTRL LEFTSHIFT M MINUS N NUMLOCK O P PAGEDOWN PAGEUP Q R RIGHT RIGHTALT RIGHTBRACE RIGHTCTRL RIGHTSHIFT S SCROLLLOCK SEMICOLON SLASH SPACE T TAB U UP V W X Y Z
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/004/002: Permission denied
libusb: error [_get_usbfs_fd] libusb requires write access to USB device nodes.
[2016-11-27 16:11:53.572569] [0xb71f3d80] [error] Error opening G13 device
[2016-11-27 16:11:53.572606] [0xb71f3d80] [info] Found 0 G13s
Czy ktoś może to przetłumaczyć na Polski
bartek@bartek-HP-Pavilion-dv6-NoteBook-PC:~/Pobrane/g13$ ./g13d
[2016-11-27 16:11:53.563565] [0xb71f3d80] [info] set log level to info
[2016-11-27 16:11:53.564238] [0xb71f3d80] [info] Known keys on G13:
[2016-11-27 16:11:53.564352] [0xb71f3d80] [info] BD DOWN G1 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G2 G20 G21 G22 G3 G4 G5 G6 G7 G8 G9 L1 L2 L3 L4 LEFT LIGHT LIGHT2 LIGHT_STATE M1 M2 M3 MISC_TOGGLE MR TOP UNDEF1 UNDEF3
[2016-11-27 16:11:53.564420] [0xb71f3d80] [info] Known keys to map to:
[2016-11-27 16:11:53.564530] [0xb71f3d80] [info] 0 1 2 3 4 5 6 7 8 9 A APOSTROPHE B BACKSLASH BACKSPACE C CAPSLOCK COMMA D DELETE DOT DOWN E END ENTER EQUAL ESC F F1 F10 F11 F12 F2 F3 F4 F5 F6 F7 F8 F9 G GRAVE H HOME I INSERT J K KP0 KP1 KP2 KP3 KP4 KP5 KP6 KP7 KP8 KP9 KPASTERISK KPDOT KPMINUS KPPLUS L LEFT LEFTALT LEFTBRACE LEFTCTRL LEFTSHIFT M MINUS N NUMLOCK O P PAGEDOWN PAGEUP Q R RIGHT RIGHTALT RIGHTBRACE RIGHTCTRL RIGHTSHIFT S SCROLLLOCK SEMICOLON SLASH SPACE T TAB U UP V W X Y Z
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/004/002: Permission denied
libusb: error [_get_usbfs_fd] libusb requires write access to USB device nodes.
[2016-11-27 16:11:53.572569] [0xb71f3d80] [error] Error opening G13 device
[2016-11-27 16:11:53.572606] [0xb71f3d80] [info] Found 0 G13s
Czy ktoś może to przetłumaczyć na Polski
-
namok
- Przebojowy Jelonek
- Posty: 1701
- Rejestracja: 01 mar 2008, 12:21
- Płeć: Mężczyzna
- Wersja Ubuntu: 16.04
- Środowisko graficzne: Unity
- Architektura: x86_64
- Kontakt:
Re: Logitech g13 - jak uruchomić?
Ta klawiatura to na usb? Chyba tu jest problem:
Trzebaby nadać odpowiednie uprawnienia dla urządzenia.libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/004/002: Permission denied
libusb: error [_get_usbfs_fd] libusb requires write access to USB device nodes.
Re: Logitech g13 - jak uruchomić?
Tak zgadza się na USB . Można troszkę jasniej jak dodawać takie uprawnienia.
-
namok
- Przebojowy Jelonek
- Posty: 1701
- Rejestracja: 01 mar 2008, 12:21
- Płeć: Mężczyzna
- Wersja Ubuntu: 16.04
- Środowisko graficzne: Unity
- Architektura: x86_64
- Kontakt:
Re: Logitech g13 - jak uruchomić?
Nie miałem za bardzo czasu aby więcej pisać. Podaj wynik polecenia
Kod: Zaznacz cały
lsusbRe: Logitech g13 - jak uruchomić?
Bus 002 Device 002: ID 064e:c107 Suyin Corp. HP webcam [dv6-1190en]
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 046d:c21c Logitech, Inc. G13 Advanced Gameboard
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Udało mi się. Logitech g13 działa na ubuntu 16.10. Nie wiem czemu ale zaskoczyło zresetowałem komputer podpiołem pod inne wejscie usb i zaskoczyło
Bus 002 Device 002: ID 064e:c107 Suyin Corp. HP webcam [dv6-1190en]
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 046d:c21c Logitech, Inc. G13 Advanced Gameboard
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Proszę odpowiedz mi na jedno pytanie. Czy za każdym razem kiedy będę chciał uruchomić tego logitecha g13 będę musiał w terminalu wpisywąć polecenie.
Gdy by ktoś miał problem z podłączeniem tego g13 uruchomiłem go tą metodą :
README
Notes:
I've only tried this on Ubuntu 11.04 64 bit version. No promises that it will work
on your version even if it's the same.
Requirements:
libusb-1.0
if you don't have it, you can get it by "sudo apt-get install libusb-1.0"
Java version 1.6 or higher
Download:
Download zip file from https://github.com/Tetz95/linux-g13-dri ... er/distros
Unzip into your favorite directory
Build:
Open a console (command prompt)
Go to the directory where you unzipped your download
type "make"
Running Application:
Run the config tool first!
In a command prompt go to the directory where you unzipped your download
and type "java -jar Linux-G13-GUI.jar"
This will bring up the UI and create the initial files needed for your driver.
All config files are saved in $(HOME)/.g13
Run the driver
In a command prompt go to the directory where you unzipped your download
and type "sudo ./Linux-G13-Driver"
If you are configuring the application while the driver is running, the driver will
not pick up changes unless you select a different bindings set or you can restart
the driver.
The top 4 buttons under the LCD screen select the bindings.
The joystick currently only supports key mappings.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 046d:c21c Logitech, Inc. G13 Advanced Gameboard
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Udało mi się. Logitech g13 działa na ubuntu 16.10. Nie wiem czemu ale zaskoczyło zresetowałem komputer podpiołem pod inne wejscie usb i zaskoczyło
Bus 002 Device 002: ID 064e:c107 Suyin Corp. HP webcam [dv6-1190en]
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 046d:c21c Logitech, Inc. G13 Advanced Gameboard
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Proszę odpowiedz mi na jedno pytanie. Czy za każdym razem kiedy będę chciał uruchomić tego logitecha g13 będę musiał w terminalu wpisywąć polecenie.
Gdy by ktoś miał problem z podłączeniem tego g13 uruchomiłem go tą metodą :
README
Notes:
I've only tried this on Ubuntu 11.04 64 bit version. No promises that it will work
on your version even if it's the same.
Requirements:
libusb-1.0
if you don't have it, you can get it by "sudo apt-get install libusb-1.0"
Java version 1.6 or higher
Download:
Download zip file from https://github.com/Tetz95/linux-g13-dri ... er/distros
Unzip into your favorite directory
Build:
Open a console (command prompt)
Go to the directory where you unzipped your download
type "make"
Running Application:
Run the config tool first!
In a command prompt go to the directory where you unzipped your download
and type "java -jar Linux-G13-GUI.jar"
This will bring up the UI and create the initial files needed for your driver.
All config files are saved in $(HOME)/.g13
Run the driver
In a command prompt go to the directory where you unzipped your download
and type "sudo ./Linux-G13-Driver"
If you are configuring the application while the driver is running, the driver will
not pick up changes unless you select a different bindings set or you can restart
the driver.
The top 4 buttons under the LCD screen select the bindings.
The joystick currently only supports key mappings.
-
namok
- Przebojowy Jelonek
- Posty: 1701
- Rejestracja: 01 mar 2008, 12:21
- Płeć: Mężczyzna
- Wersja Ubuntu: 16.04
- Środowisko graficzne: Unity
- Architektura: x86_64
- Kontakt:
Re: Logitech g13 - jak uruchomić?
Moje cudowne polecenie nic nie zrobiło tylko wyświetliło informacje. Pracę wykonało skopiowanie pliku '91-g13.rules' w odpowiednie miejsce. Jeśli chcesz wiedzieć co dane polecenie znaczy to w terminalu Jeśli angielski jest problemem to instalujesz spolszczenie:
Aby program uruchamiał się automatycznie możesz dodać go do autostartu.
Dlaczego przstałeś używać znaczników? To co piszesz jest nieczytelne.
Kod: Zaznacz cały
man nazwa_poleceniaKod: Zaznacz cały
sudo apt-get install manpages-plDlaczego przstałeś używać znaczników? To co piszesz jest nieczytelne.
Kto jest online
Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 20 gości