Strona 1 z 1
Podczas sprawdzania napędu /home znaleziono błędy.
: 17 maja 2011, 09:57
autor: Marek Ślepy
Podczas sprawdzania napędu /home znaleziono błędy. Informacja taka pojawia się przed każdym uruchomieniem i zaczyna się sprawdzanie dysków.
Wtedy wciskam C, następnie F znów C na konie I, i jak się nie wyłączy po drodze to już wystartuje. I tak codziennie. Próbowałem już to zdiagnozować, ale bez rezultatu.Tylko coś tam wyszło ,jak pamiętam, jakieś dwa uszkodzenia w dysku.
Z czym się zwracam i o co proszę: zdiagnozować, jak się da naprawić, jak się nie da naprawić , to wyłączyć.
Trwa to już chyba rok. Czasami włączam inny system operacyjny, i tam tego nie ma.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 17 maja 2011, 10:21
autor: marcin1982
Sprawdź czy coś takiego pomoże:
potem:
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 17 maja 2011, 10:35
autor: Marek Ślepy
Powtórzyłem dwa razy, sam się wyłączył, ale przy włączaniu ta sama procedura. Nie pomogło.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 18 maja 2011, 19:04
autor: Marek Ślepy
Odświeżę temat.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 18 maja 2011, 19:55
autor: pioruns
Zainstaluj pakiet smartmontools i wykonaj wewnętrzny test powierzchni dysku.
Po zakończeniu testu (będzie pisało, za ile minut powinno się skończyć, poczekaj trochę dłużej, dla pewności), pokaż wynik
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 18 maja 2011, 21:21
autor: Marek Ślepy
Czy tak jest prawidłowo:
Wpisałem pierwszą komendę, i taka odpowiedź.
Kod: Zaznacz cały
marek@marek-G33M-S2:~$ sudo smartctl --test=long /dev/sda
[sudo] password for marek:
sudo: smartctl: command not found
Zainstalowałem przy pomocy Gentrum Oprogeamowania, ale GSmartControl, i taka odpowiedź. A w Synaptic jest zainstalowany smartmontools
Kod: Zaznacz cały
marek@marek-G33M-S2:~$ sudo smartctl --test=long /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 179 minutes for test to complete.
Test will complete after Thu May 19 00:02:25 2011
Use smartctl -X to abort test.
marek@marek-G33M-S2:~$
Teraz mam czekać 179 minut , czy wszystko jest prawidłowo? Nie otworzyło się żadne okno , rozumiem że to się dzieje w sposób taki, ukryty, tylko na czas.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 19 maja 2011, 01:02
autor: Marek Ślepy
Wynik.
Kod: Zaznacz cały
marek@marek-G33M-S2:~$ sudo smartctl --all /dev/sda
[sudo] password for marek:
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.9 family
Device Model: ST3400833AS
Serial Number: 3PM0W070
Firmware Version: 3.AAD
User Capacity: 400,088,457,216 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu May 19 00:58:42 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 179) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 086 006 Pre-fail Always - 179962224
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2474
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 2
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 547309184
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 9273
10 Spin_Retry_Count 0x0013 100 098 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2826
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 059 051 045 Old_age Always - 41 (Lifetime Min/Max 21/43)
194 Temperature_Celsius 0x0022 041 049 000 Old_age Always - 41 (0 15 0 0)
195 Hardware_ECC_Recovered 0x001a 054 053 000 Old_age Always - 93091391
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1746 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1746 occurred at disk power-on lifetime: 9248 hours (385 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e 88 93 ee
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e 88 93 ee 00 01:01:33.613 SET MAX ADDRESS EXT
27 00 00 6e 88 93 e0 00 01:01:33.544 READ NATIVE MAX ADDRESS EXT
37 00 00 6e 88 93 ee 00 01:01:31.427 SET MAX ADDRESS EXT
27 00 01 6e 88 93 e0 00 01:01:31.360 READ NATIVE MAX ADDRESS EXT
37 00 01 6e 88 93 ee 00 01:01:31.130 SET MAX ADDRESS EXT
Error 1745 occurred at disk power-on lifetime: 9248 hours (385 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e 88 93 ee
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e 88 93 ee 00 01:01:27.782 SET MAX ADDRESS EXT
27 00 00 6e 88 93 e0 00 01:01:27.358 READ NATIVE MAX ADDRESS EXT
37 00 00 6e 88 93 ee 00 01:01:31.427 SET MAX ADDRESS EXT
27 00 01 af 90 93 e0 00 01:01:31.360 READ NATIVE MAX ADDRESS EXT
29 00 01 af 90 93 e0 00 01:01:31.130 READ MULTIPLE EXT
Error 1744 occurred at disk power-on lifetime: 9248 hours (385 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e 88 93 ee
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e 88 93 ee 00 00:57:09.990 SET MAX ADDRESS EXT
27 00 00 6e 88 93 e0 00 00:57:09.921 READ NATIVE MAX ADDRESS EXT
37 00 00 6e 88 93 ee 00 00:57:09.693 SET MAX ADDRESS EXT
27 00 01 6e 88 93 e0 00 00:57:09.615 READ NATIVE MAX ADDRESS EXT
37 00 01 6e 88 93 ee 00 00:57:09.456 SET MAX ADDRESS EXT
Error 1743 occurred at disk power-on lifetime: 9248 hours (385 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e 88 93 ee
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e 88 93 ee 00 00:57:09.990 SET MAX ADDRESS EXT
27 00 00 6e 88 93 e0 00 00:57:09.921 READ NATIVE MAX ADDRESS EXT
37 00 00 6e 88 93 ee 00 00:57:09.693 SET MAX ADDRESS EXT
27 00 01 af 90 93 e0 00 00:57:09.615 READ NATIVE MAX ADDRESS EXT
29 00 01 af 90 93 e0 00 00:57:09.456 READ MULTIPLE EXT
Error 1742 occurred at disk power-on lifetime: 9216 hours (384 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 6e 88 93 ee
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
37 00 01 6e 88 93 ee 00 00:02:17.028 SET MAX ADDRESS EXT
27 00 00 6e 88 93 e0 00 00:02:14.921 READ NATIVE MAX ADDRESS EXT
37 00 00 6e 88 93 ee 00 00:02:14.854 SET MAX ADDRESS EXT
27 00 01 6e 88 93 e0 00 00:02:14.624 READ NATIVE MAX ADDRESS EXT
37 00 01 6e 88 93 ee 00 00:02:14.546 SET MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 9273 -
# 2 Extended offline Aborted by host 20% 9269 -
# 3 Short offline Completed without error 00% 5927 -
# 4 Short offline Completed without error 00% 5920 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 19 maja 2011, 17:44
autor: pioruns
Masowe błędy odczytu danych z powierzchni talerzy, prawie 2 tysiące zarejestrowanych błędów w logu SMART, gdzie ostatnie pięć dotyczy błędów odczytu, co potwierdza wartości widoczne w atrybutach. Większość danych jest odzyskiwana i naprawiana przez sumy kontrolne ECC oraz wielokrotne ponowienia odczytu, dlatego w miarę możesz na codzień pracować. Dysk sypie się ze starości albo ma problemy z głowicami. Ja bym zgrał wszystko z niego i kupił nowy dysk.
Jeśli chcesz na nim dalej pracować, musisz zrobić pełny low-level format narzędziem od producenta, albo przejechać go pełnym read-write-verify innym programem narzędziowym, jak MHDD, Spinrite (płatny) itd. Ponadto musisz regularnie sprawdzać systemy plików ze skanowaniem powierzchni, bo masz już parę (dosłownie 2) realokowanych sektorów; nie wykluczone, że jest ich więcej, tylko nie zostały jeszcze wykryte (bo nic tam akurat nie zapisujesz), a pojawią się później, po skanowaniu programem narzędziowym lub low-level- formacie, albo po kolejnej serii zapisów w wadliwym sektorze.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 19 maja 2011, 20:17
autor: Marek Ślepy
Dziękuję. To jest nowy sprzęt w grudniu będzie miał cztery lata Komputer VOBIS DIGITAL VP Q6600 XPOWER GT A problemy z głowicami to jak wykluczyć ,albo potwierdzić. W czasie pracy to nie ma kłopotu , jedynie przy uruchamianiu.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 20 maja 2011, 07:42
autor: k2cl
Marku, najwyraźniej określenie "nowy sprzęt" ma dla Ciebie dosyć niecodzienne znaczenie. Jeżeli dysk ma trzy i pół roku, z pewnością nie jest nowy. Niestety, niektóre urządzenia (w tym dyski twarde) mają to do siebie, że czasem padają "ze starości". Na Twoim miejscu wymieniłbym dysk tak szybko, jak to możliwe. Unikniesz konieczności zakładania wątku "Jak odzyskać dane z uszkodzonego dysku twardego"...
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 20 maja 2011, 11:43
autor: Marek Ślepy
Dzięki, tylko to pewnie spory wydatek no i nie wiem czego szukać. Muszę sprawdzić w papierach zakupu.
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 22 maja 2011, 21:01
autor: linuxozaurus
jak piszesz ze komputer kupiłeś 4 lata temu przy założeniu ze nie wymieniałeś dysku nie ma co szukać w papierach bo jest dawno po gwarancji kup nowy
Re: Podczas sprawdzania napędu /home znaleziono błędy.
: 09 wrz 2011, 15:16
autor: zupazupa
Witam, podpinam się pod temat, bo mam podobny problem (błąd na partycji / i /home podczas sprawdzania), tylko, że lapek ma dopiero rok.
Jeszcze tydzień temu było wszystko ok, natomiast dziś był gość z serwisu wymienić podzespół z bluetoothem i tuż po tym wystąpiły te błędy. Mam takie pytanie - może trochę głupie - czy to może mieć jakiś związek, czy tylko taki zbieg okoliczności? A tak w ogóle te błędy to są fizycznie na dysku - w sensie, że mogę to reklamować, czy to jest błąd w samym systemie plików?