Po aktualizacji atheros nie działa
: 21 gru 2008, 15:39
Cześć. Mam problem z moją kartą sieciową Atheros AR5212(seria AR5xxx)
trochę o mnie:
Ubuntu 8.04
Kernel 2.6.24-22-generic (#1 SMP Mon Nov 24 18:32:42 UTC 2008)
GCC 4.2.4 (i486-linux-gnu)
Gnome 2.22.3 (Ubuntu 2008-07-09)
ndiswrapper 1.52
wicd 1.5.6
Do tej pory używałem drivera net5211 i było dobrze. Ściągnąłem poprawki...
dmesg:
~$ iwconfig
~$ lspci
Na karcie mam 2 diodki migają na zmianę( na windzie migały obie naraz jak działało)
Jakiś pomysł?
EDIT:
Dalej nie działa.
Czy ktoś ma jakiś pomysł dlaczego
albo co oznaczają naprzemiennie migające diodki?
trochę o mnie:
Ubuntu 8.04
Kernel 2.6.24-22-generic (#1 SMP Mon Nov 24 18:32:42 UTC 2008)
GCC 4.2.4 (i486-linux-gnu)
Gnome 2.22.3 (Ubuntu 2008-07-09)
ndiswrapper 1.52
wicd 1.5.6
Do tej pory używałem drivera net5211 i było dobrze. Ściągnąłem poprawki...
...i przestało być dobrze. Reinstalowałem sterownik, ściągnąłem go jeszcze raz, sprawdziłem czy nie gryzie się z ath_pci, sprawdziłem czy karta się nie obluzowała, sprawdziłem czy slot PCI działa, przeszukałem /etc/modprobe.d/blacklist. Oczywiście nie pomogło. Sprawdziłem na windzie - działa.libgnutls-dev (2.0.4-1ubuntu2.2) to 2.0.4-1ubuntu2.3
libgnutls13 (2.0.4-1ubuntu2.2) to 2.0.4-1ubuntu2.3
libgnutlsxx13 (2.0.4-1ubuntu2.2) to 2.0.4-1ubuntu2.3
linux-restricted-modules-common (2.6.24.14-22.53) to 2.6.24.14-23.54
dmesg:
...
[ 47.097068] ndiswrapper: using IRQ 21
[ 47.294904] wlan0: ethernet device 00:30:4f:6a:14:38 using serialized NDIS driver: net5211, version: 0x20004, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 168C:0013.5.conf
[ 47.294919] wlan0: encryption modes supported: WEP; TKIP with WPA; AES/CCMP with WPA
[ 47.302879] usbcore: registered new interface driver ndiswrapper
[ 47.303571] Linux agpgart interface v0.102
[ 47.695389] ndiswrapper: changing interface name from 'wlan0' to 'wlan1'
[ 47.695429] udev: renamed network interface wlan0 to wlan1
[ 47.710421] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
[ 47.710426] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 21
[ 47.710432] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 47.710570] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
[ 47.821650] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
[ 47.821654] ACPI: PCI Interrupt 0000:00:06.1 -> Link [AAZA] -> GSI 20 (level, low) -> IRQ 20
[ 47.821668] PCI: Setting latency timer of device 0000:00:06.1 to 64
...
[trochę komunikatów nie na temat]
...
[ 56.322619] eth0: no link during initialization.
[ 58.115006] NET: Registered protocol family 31
...
[informacje o bluetooth]
...
[ 61.259392] ppdev: user-space parallel port driver
[ 61.478629] NET: Registered protocol family 10
[ 61.478803] lo: Disabled Privacy Extensions
[ 61.479163] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 61.786451] audit(1229339061.511:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5910 profile="/usr/sbin/cupsd" namespace="default"
[ 833.845258] ADDRCONF(NETDEV_UP): wlan1: link is not ready
~$ iwconfig
wlan1 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
~$ lspci
00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3)
00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a3)
00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3)
00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2)
00:06.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)
00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3)
00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:06.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213 Multiprotocol MAC/baseband processor (rev 01)
01:0b.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 03)
02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 03)
03:00.0 VGA compatible controller: nVidia Corporation GeForce 8600 GTS (rev a1)
Na karcie mam 2 diodki migają na zmianę( na windzie migały obie naraz jak działało)
Jakiś pomysł?
EDIT:
Dalej nie działa.
Czy ktoś ma jakiś pomysł dlaczego
wlan1: link not ready
albo co oznaczają naprzemiennie migające diodki?