Chciałem se obraz płyty nagrać....i przykra niespodzianka:
Kod: Zaznacz cały
Devices
-----------------------
ASUS DRW-2014L1T 1.02 (/dev/sr1, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]
PLEXTOR DVDR PX-810SA 1.01 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]
System
-----------------------
K3b Version: 2.0.2
KDE Version: 4.11.3
QT Version: 4.8.4
Kernel: 3.11.0-15-generic
Used versions
-----------------------
cdrecord: 3.1a22
cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
cdrecord: Warning: Cannot read drive buffer.
cdrecord: Warning: The DMA speed test has been skipped.
Cdrecord-ProDVD-ProBD-Clone 3.01a22 (x86_64-unknown-linux-gnu) Copyright (C) 1995-2014 Joerg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.9'.
Driveropts: 'burnfree'
atapi: 1
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'PLEXTOR '
Identifikation : 'DVDR PX-810SA '
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: DVD-R sequential recording
Profile: DVD+R/DL
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-R/DL layer jump recording
Profile: DVD-R/DL sequential recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD-RAM
Profile: Removable Disk
Profile: DVD-R sequential recording (current)
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R
Profile: CD-ROM
Using generic SCSI-3/mmc-2 DVD-R/DVD-RW/DVD-RAM driver (mmc_dvd).
Driver flags : NO-CD DVD MMC-3 SWABAUDIO BURNFREE
Supported modes: PACKET SAO LAYER_JUMP
Drive buf size : 1605632 = 1568 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 1238 MB
Total size: 1238 MB = 633984 sectors
Current Secsize: 2048
Total power on hours: 75040
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 1664512
Reducing transfer size from 64512 to 32768 bytes.
Starting to write CD/DVD/BD at speed 16 in real SAO mode for single session.
Last chance to quit, starting real write in 3 seconds.
2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Starting new track at sector: 0
Track 01: 0 of 1238 MB written.
Track 01: 1 of 1238 MB written (fifo 86%) 24,9x.
cdrecord: Błąd wejścia/wyjścia. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 03 00 00 00 10 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0E 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 69.690s timeout 200s
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
write track data: error after 1572864 bytes
Writing time: 74.831s
Average write speed 12,5x.
Fixating...
Fixating time: 0.005s
cdrecord: fifo had 176 puts and 49 gets.
cdrecord: fifo was 0 times empty and 3 times full, min fill was 82%.
cdrecord command:
-----------------------
/opt/schily/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=16 -sao driveropts=burnfree -data -tsize=633984s -
Kiedyś pomagało przestawianie z SAO na DAO, teraz nawet z DAO nie działa... program proponuje nagrywanie w trybie TAO, ale napęd takiego trybu nie obsługuje.
Wie ktoś gdzie problem leży?
//bear7: Polecenia, wyniki poleceń, błędy, komunikaty, zawartość plików konfiguracyjnych oraz systemowych, na forum umieszczamy pomiędzy znacznikami CODE.