brak dzwieku w tvtime (i innych programach do TV)

[EloElo]

witam!
mam problem z dzwiekiem (tzn wogole go nie ma)
podczas ogladania TV u mnie na kompie,

po wpisaniu lspci mam info o karcie takie
03:02.0 Multimedia controller: Philips Semiconductors SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)

no i uzywam do ogladania tvtime

co mam z tym zrobic zeby miec ten dzwiek??
z gory dzieki za pomoc!

[rrroback]

1. Albo trzeba ustawić PAL-DK
2. Albo uruchomić alsamixer (wpisać w konsoli alsamixer) i odmutować wyjście CD lub AUX.
Jako początkujący tyle mogę podpowiedzieć

[ilin]

Nie wiemy co to za karta.

Pokaz zawartośc pliku /var/log/dmesg

[salvadhor]

Jak widzę saa7134 to już mnie brzuch boli
Karta nie ma wyjścia audio wyprowadzanego na wejście w karcie muzycznej. Trzeba łapać software'owo dźwięk z karty TV i przekierowywać na muzyczną. Na forum było to już parę razy opisywane - słowa kluczowe 'saa7134' (lub aver tv) 'sox'.

[ilin]

Nie wszystkie na saa7134 tak mają więc poprosilem o dmesg aby jednoznacznie stwierdzic jakiej metody trzeba użyć.

[EloElo]

zawartośc pliku /var/log/dmesg

Kod: Zaznacz cały

[    0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 07:42:25 UTC 2008 (Ubuntu 2.6.22-14.52-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000001fe30000 (usable)
[    0.000000]  BIOS-e820: 000000001fe30000 - 000000001fe41620 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001fe41620 - 000000001ff30000 (usable)
[    0.000000]  BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
[    0.000000]  BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 511MB LOWMEM available.
[    0.000000] found SMP MP-table at 000ff780
[    0.000000] Entering add_active_range(0, 0, 130864) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   130864
[    0.000000]   HighMem    130864 ->   130864
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   130864
[    0.000000] On node 0 totalpages: 130864
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 990 pages used for memmap
[    0.000000]   Normal zone: 125778 pages, LIFO batch:31
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000] DMI 2.3 present.
[    0.000000] ACPI: RSDP signature @ 0xC00F6140 checksum 0
[    0.000000] ACPI: RSDP 000F6140, 0014 (r0 ACPIAM)
[    0.000000] ACPI: RSDT 1FF30000, 0034 (r1 INTEL  D875BZLK 20030916 MSFT       97)
[    0.000000] ACPI: FACP 1FF30200, 0081 (r2 INTEL  D875BZLK 20030916 MSFT       97)
[    0.000000] ACPI: DSDT 1FF30370, 40F3 (r1 INTEL  D875BZLK        1 MSFT  100000D)
[    0.000000] ACPI: FACS 1FF40000, 0040
[    0.000000] ACPI: APIC 1FF30300, 0068 (r1 INTEL  D875BZLK 20030916 MSFT       97)
[    0.000000] ACPI: ASF! 1FF34470, 0099 (r16 LEGEND I865PASF        1 MSFT  100000D)
[    0.000000] ACPI: WDDT 1FF34509, 0040 (r1 INTEL  OEMWDDT         1 MSFT  100000D)
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 15:2 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] Processor #1 15:2 APIC version 20
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:decf0000)
[    0.000000] Built 1 zonelists.  Total pages: 129842
[    0.000000] Kernel command line: root=UUID=9681a8d7-63a4-42f1-8102-64bcfb3b4327 ro quiet splash locale=pl_PL
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Detected 2394.118 MHz processor.
[   20.195915] Console: colour VGA+ 80x25
[   20.196121] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[   20.196328] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[   20.206030] Memory: 506892k/523456k available (2015k kernel code, 15760k reserved, 915k data, 364k init, 0k highmem)
[   20.206040] virtual kernel memory layout:
[   20.206042]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   20.206043]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   20.206044]     vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
[   20.206045]     lowmem  : 0xc0000000 - 0xdff30000   ( 511 MB)
[   20.206046]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   20.206048]       .data : 0xc02f7e86 - 0xc03dce84   ( 915 kB)
[   20.206049]       .text : 0xc0100000 - 0xc02f7e86   (2015 kB)
[   20.206052] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   20.206089] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[   20.285977] Calibrating delay using timer specific routine.. 4792.11 BogoMIPS (lpj=9584230)
[   20.286001] Security Framework v1.0.0 initialized
[   20.286007] SELinux:  Disabled at boot.
[   20.286021] Mount-cache hash table entries: 512
[   20.286158] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[   20.286171] CPU: Trace cache: 12K uops, L1 D cache: 8K
[   20.286175] CPU: L2 cache: 512K
[   20.286177] CPU: Physical Processor ID: 0
[   20.286180] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000
[   20.286191] Compat vDSO mapped to ffffe000.
[   20.286204] Checking 'hlt' instruction... OK.
[   20.302068] SMP alternatives: switching to UP code
[   20.302517] Early unpacking initramfs... done
[   20.644565] ACPI: Core revision 20070126
[   20.644623] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   20.646844] CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[   20.646864] SMP alternatives: switching to SMP code
[   20.647010] Booting processor 1/1 eip 3000
[   20.657146] Initializing CPU#1
[   20.737223] Calibrating delay using timer specific routine.. 4788.37 BogoMIPS (lpj=9576750)
[   20.737233] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
[   20.737245] CPU: Trace cache: 12K uops, L1 D cache: 8K
[   20.737248] CPU: L2 cache: 512K
[   20.737250] CPU: Physical Processor ID: 0
[   20.737253] CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000
[   20.737432] CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
[   20.737477] Total of 2 processors activated (9580.49 BogoMIPS).
[   20.737605] ENABLING IO-APIC IRQs
[   20.737789] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   20.885112] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   20.905244] Brought up 2 CPUs
[   20.952814] migration_cost=97
[   20.953014] Booting paravirtualized kernel on bare hardware
[   20.953083] Time: 19:46:27  Date: 05/12/108
[   20.953105] NET: Registered protocol family 16
[   20.953218] EISA bus registered
[   20.953225] ACPI: bus type pci registered
[   20.954766] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
[   20.954769] PCI: Using configuration type 1
[   20.954771] Setting up standard PCI resources
[   20.968798] ACPI: EC: Look up EC in DSDT
[   20.972769] ACPI: Interpreter enabled
[   20.972774] ACPI: (supports S0 S1 S4 S5)
[   20.972796] ACPI: Using IOAPIC for interrupt routing
[   20.980817] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   20.980846] PCI: Probing PCI hardware (bus 00)
[   20.981373] PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[   20.981377] PCI quirk: region 0500-053f claimed by ICH4 GPIO
[   20.982024] PCI: Transparent bridge - 0000:00:1e.0
[   20.982058] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   20.982174] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[   20.982254] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[   20.982330] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[   20.984967] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[   20.985152] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[   20.985340] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[   20.985515] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[   20.985693] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[   20.985869] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[   20.986046] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[   20.986221] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[   20.986411] ACPI: Power Resource [URP1] (off)
[   20.986461] ACPI: Power Resource [FDDP] (off)
[   20.986497] ACPI: Power Resource [LPTP] (off)
[   20.986519] Linux Plug and Play Support v0.97 (c) Adam Belay
[   20.986533] pnp: PnP ACPI init
[   20.986546] ACPI: bus type pnp registered
[   20.990326] pnp: PnP ACPI: found 14 devices
[   20.990329] ACPI: ACPI bus type pnp unregistered
[   20.990334] PnPBIOS: Disabled by ACPI PNP
[   20.990418] PCI: Using ACPI for IRQ routing
[   20.990422] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   20.995810] NET: Registered protocol family 8
[   20.995813] NET: Registered protocol family 20
[   20.995972] pnp: 00:0c: ioport range 0x400-0x47f has been reserved
[   20.995976] pnp: 00:0c: ioport range 0x680-0x6ff has been reserved
[   20.995979] pnp: 00:0c: ioport range 0x500-0x53f has been reserved
[   20.995983] pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
[   20.995986] pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[   20.995990] pnp: 00:0c: iomem range 0xfed20000-0xfed9ffff could not be reserved
[   20.996000] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
[   20.996003] pnp: 00:0d: iomem range 0xc0000-0xdffff could not be reserved
[   20.996007] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[   20.996010] pnp: 00:0d: iomem range 0x100000-0x1fffffff could not be reserved
[   20.996820] Time: tsc clocksource has been installed.
[   21.026435] PCI: Bridge: 0000:00:01.0
[   21.026438]   IO window: disabled.
[   21.026444]   MEM window: fc800000-fe8fffff
[   21.026449]   PREFETCH window: e4700000-f46fffff
[   21.026454] PCI: Bridge: 0000:00:03.0
[   21.026457]   IO window: a000-afff
[   21.026462]   MEM window: fe900000-fe9fffff
[   21.026466]   PREFETCH window: disabled.
[   21.026471] PCI: Bridge: 0000:00:1e.0
[   21.026474]   IO window: b000-bfff
[   21.026480]   MEM window: fea00000-feafffff
[   21.026485]   PREFETCH window: disabled.
[   21.026506] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   21.026520] NET: Registered protocol family 2
[   21.065001] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   21.065040] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[   21.065138] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[   21.065203] TCP: Hash tables configured (established 16384 bind 16384)
[   21.065206] TCP reno registered
[   21.077103] checking if image is initramfs... it is
[   21.527937] Switched to high resolution mode on CPU 0
[   21.528190] Switched to high resolution mode on CPU 1
[   21.762490] Freeing initrd memory: 7346k freed
[   21.762918] audit: initializing netlink socket (disabled)
[   21.762932] audit(1213299987.172:1): initialized
[   21.766019] VFS: Disk quotas dquot_6.5.1
[   21.766096] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   21.766208] io scheduler noop registered
[   21.766211] io scheduler anticipatory registered
[   21.766214] io scheduler deadline registered
[   21.766232] io scheduler cfq registered (default)
[   21.766322] Boot video device is 0000:01:00.0
[   21.766542] isapnp: Scanning for PnP cards...
[   22.119898] isapnp: No Plug & Play device found
[   22.151638] Real Time Clock Driver v1.12ac
[   22.151760] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   22.151851] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   22.152693] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   22.153674] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   22.153971] input: Macintosh mouse button emulation as /class/input/input0
[   22.154088] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[   22.156971] serio: i8042 KBD port at 0x60,0x64 irq 1
[   22.156980] serio: i8042 AUX port at 0x60,0x64 irq 12
[   22.157229] mice: PS/2 mouse device common for all mice
[   22.157398] EISA: Probing bus 0 at eisa.0
[   22.157440] EISA: Detected 0 cards.
[   22.157543] TCP cubic registered
[   22.157556] NET: Registered protocol family 1
[   22.157580] Using IPI No-Shortcut mode
[   22.157767]   Magic number: 12:153:799
[   22.157890]   hash matches device ptyr7
[   22.158183] Freeing unused kernel memory: 364k freed
[   22.184203] input: AT Translated Set 2 keyboard as /class/input/input1
[   23.395571] AppArmor: AppArmor initialized<5>audit(1213299988.672:2):  type=1505 info="AppArmor initialized" pid=1143
[   23.403389] fuse init (API version 7.8)
[   23.409355] Failure registering capabilities with primary security module.
[   23.440346] ACPI: Processor [CPU1] (supports 8 throttling states)
[   23.440373] ACPI: Processor [CPU2] (supports 8 throttling states)
[   24.119614] usbcore: registered new interface driver usbfs
[   24.119657] usbcore: registered new interface driver hub
[   24.119706] usbcore: registered new device driver usb
[   24.121053] USB Universal Host Controller Interface driver v3.0
[   24.121130] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[   24.121146] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   24.121152] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   24.121338] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   24.121373] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000cc00
[   24.121565] usb usb1: configuration #1 chosen from 1 choice
[   24.121612] hub 1-0:1.0: USB hub found
[   24.121631] hub 1-0:1.0: 2 ports detected
[   24.219293] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI

[EloElo]

niezmiescilo mi sie w jednym
jak mi podacie o ktore wersy dokladnie chodzi to reszte pousuwam

Kod: Zaznacz cały

[   24.219300] Copyright (c) 1999-2006 Intel Corporation.
[   24.223502] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
[   24.223522] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   24.223530] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   24.223585] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   24.223626] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000d000
[   24.223829] usb usb2: configuration #1 chosen from 1 choice
[   24.223901] hub 2-0:1.0: USB hub found
[   24.223916] hub 2-0:1.0: 2 ports detected
[   24.327230] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[   24.327246] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   24.327252] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   24.327296] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   24.327329] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d400
[   24.327486] usb usb3: configuration #1 chosen from 1 choice
[   24.327533] hub 3-0:1.0: USB hub found
[   24.327545] hub 3-0:1.0: 2 ports detected
[   24.381419] SCSI subsystem initialized
[   24.382472] Floppy drive(s): fd0 is 1.44M
[   24.400695] libata version 2.21 loaded.
[   24.404183] FDC 0 is a National Semiconductor PC87306
[   24.431040] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
[   24.431058] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   24.431064] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   24.431110] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   24.431139] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000d800
[   24.431305] usb usb4: configuration #1 chosen from 1 choice
[   24.431358] hub 4-0:1.0: USB hub found
[   24.431368] hub 4-0:1.0: 2 ports detected
[   24.462817] usb 1-2: new full speed USB device using uhci_hcd and address 2
[   24.536167] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
[   24.536193] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   24.536201] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   24.536264] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   24.536318] ehci_hcd 0000:00:1d.7: debug port 1
[   24.536329] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[   24.536350] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebffc00
[   24.578754] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   24.578934] usb usb5: configuration #1 chosen from 1 choice
[   24.578986] hub 5-0:1.0: USB hub found
[   24.578998] hub 5-0:1.0: 8 ports detected
[   24.682639] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 18 (level, low) -> IRQ 18
[   24.682657] PCI: Setting latency timer of device 0000:02:01.0 to 64
[   24.837366] e1000: 0000:02:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:07:e9:6a:11:3f
[   24.985908] usb 1-2: device not accepting address 2, error -71
[   25.100022] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
[   25.100274] ata_piix 0000:00:1f.1: version 2.11
[   25.100297] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[   25.100306] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[   25.100362] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   25.100492] scsi0 : ata_piix
[   25.100906] scsi1 : ata_piix
[   25.101334] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
[   25.101340] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
[   25.261773] ata1.00: ATA-5: ST340016A, 3.10, max UDMA/100
[   25.261778] ata1.00: 78165360 sectors, multi 16: LBA 
[   25.269752] ata1.00: configured for UDMA/100
[   25.648769] usb 5-4: new high speed USB device using ehci_hcd and address 3
[   25.752773] ata2.00: ATAPI: Hewlett-Packard CD-Writer Plus 8100, 1.0g, max MWDMA1
[   25.752781] ata2.01: ATAPI: HL-DT-STDVD-RAM GSA-H55L, 1.03, max UDMA/66
[   25.783180] usb 5-4: configuration #1 chosen from 1 choice
[   25.924477] ata2.00: configured for MWDMA1
[   26.020126] usb 1-2: new full speed USB device using uhci_hcd and address 4
[   26.096255] ata2.01: configured for UDMA/66
[   26.096400] scsi 0:0:0:0: Direct-Access     ATA      ST340016A        3.10 PQ: 0 ANSI: 5
[   26.102175] scsi 1:0:0:0: CD-ROM            HP       CD-Writer+ 8100  1.0g PQ: 0 ANSI: 5
[   26.103624] scsi 1:0:1:0: CD-ROM            HL-DT-ST DVD-RAM GSA-H55L 1.03 PQ: 0 ANSI: 5
[   26.103715] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[   26.103739] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
[   26.103784] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   26.103838] scsi2 : ata_piix
[   26.103920] scsi3 : ata_piix
[   26.104096] ata3: SATA max UDMA/133 cmd 0x0001ec00 ctl 0x0001e802 bmdma 0x0001dc00 irq 18
[   26.104103] ata4: SATA max UDMA/133 cmd 0x0001e400 ctl 0x0001e002 bmdma 0x0001dc08 irq 18
[   26.199612] usb 1-2: configuration #1 chosen from 1 choice
[   26.256137] usbcore: registered new interface driver libusual
[   26.284643] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   26.284651] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   26.287538] Initializing USB Mass Storage driver...
[   26.287637] scsi4 : SCSI emulation for USB Mass Storage devices
[   26.287726] usb-storage: device found at 3
[   26.287731] usb-storage: waiting for device to settle before scanning
[   26.287799] usbcore: registered new interface driver usb-storage
[   26.287805] USB Mass Storage support registered.
[   26.454660] sd 0:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
[   26.454681] sd 0:0:0:0: [sda] Write Protect is off
[   26.454688] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.454725] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.454821] sd 0:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
[   26.454852] sd 0:0:0:0: [sda] Write Protect is off
[   26.454858] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   26.454903] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   26.454914]  sda: sda1 sda2 sda3
[   26.492974] sd 0:0:0:0: [sda] Attached SCSI disk
[   26.498241] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   26.498278] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   26.498310] scsi 1:0:1:0: Attached scsi generic sg2 type 5
[   26.516967] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[   26.516975] Uniform CD-ROM driver Revision: 3.20
[   26.517070] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   26.523192] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   26.523296] sr 1:0:1:0: Attached scsi CD-ROM sr1
[   26.832880] Attempting manual resume
[   26.832885] swsusp: Resume From Partition 8:2
[   26.832887] PM: Checking swsusp image.
[   26.833376] PM: Resume from disk failed.
[   26.846756] EXT3-fs: INFO: recovery required on readonly filesystem.
[   26.846764] EXT3-fs: write access will be enabled during recovery.
[   26.857056] kjournald starting.  Commit interval 5 seconds
[   26.857068] EXT3-fs: recovery complete.
[   26.862856] EXT3-fs: mounted filesystem with ordered data mode.
[   31.279192] usb-storage: device scan complete
[   31.279823] scsi 4:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
[   31.281177] sd 4:0:0:0: [sdb] 2015232 512-byte hardware sectors (1032 MB)
[   31.281808] sd 4:0:0:0: [sdb] Write Protect is off
[   31.281816] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
[   31.281822] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   31.284045] sd 4:0:0:0: [sdb] 2015232 512-byte hardware sectors (1032 MB)
[   31.284666] sd 4:0:0:0: [sdb] Write Protect is off
[   31.284670] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
[   31.284673] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   31.284680]  sdb: sdb1
[   31.285374] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[   31.285422] sd 4:0:0:0: Attached scsi generic sg3 type 0
[   34.272717] EDAC MC: Ver: 2.0.1 Feb 12 2008
[   34.315145] EDAC i82875p: i82875p init one
[   34.315473] PCI: Unable to reserve mem region #1:1000@fecf0000 for device 0000:00:06.0
[   34.315574] EDAC MC0: Giving out device to i82875p_edac i82875p: DEV 0000:00:00.0
[   34.322776] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   34.325859] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   34.555518] Linux agpgart interface v0.102 (c) Dave Jones
[   35.467481] iTCO_vendor_support: vendor-support=0
[   35.469321] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[   35.851265] ath_hal: module license 'Proprietary' taints kernel.
[   35.852386] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[   35.916416] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[   35.919941] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0460)
[   35.920022] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   35.956070] Intel 82802 RNG detected
[   36.221285] Linux video capture interface: v2.00
[   36.294411] wlan: 0.8.4.2 (0.9.3.2)
[   36.336588] cdc_acm 1-2:1.1: ttyACM0: USB ACM device
[   36.339621] cdc_acm 1-2:1.3: ttyACM1: USB ACM device
[   36.341553] usbcore: registered new interface driver cdc_acm
[   36.341561] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
[   36.355155] parport_pc 00:09: reported by Plug and Play ACPI
[   36.355213] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   36.359242] input: PC Speaker as /class/input/input3
[   36.644100] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   36.644345] NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-9639  Mon Apr 16 20:20:06 PDT 2007
[   36.678400] ath_pci: 0.9.4.5 (0.9.3.2)
[   36.678460] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 18 (level, low) -> IRQ 18
[   37.418593] ath_rate_sample: 1.2 (0.9.3.2)
[   37.418986] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[   37.418998] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   37.419017] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[   37.419026] wifi0: mac 7.8 phy 4.5 radio 5.6
[   37.419033] wifi0: Use hw queue 1 for WME_AC_BE traffic
[   37.419037] wifi0: Use hw queue 0 for WME_AC_BK traffic
[   37.419040] wifi0: Use hw queue 2 for WME_AC_VI traffic
[   37.419043] wifi0: Use hw queue 3 for WME_AC_VO traffic
[   37.419047] wifi0: Use hw queue 8 for CAB traffic
[   37.419050] wifi0: Use hw queue 9 for beacons
[   37.461044] wifi0: Atheros 5212: mem=0xfeae0000, irq=18
[   37.568751] saa7130/34: v4l2 driver version 0.2.14 loaded
[   37.568831] ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 17 (level, low) -> IRQ 20
[   37.568846] saa7134[0]: found at 0000:03:02.0, rev: 1, irq: 20, latency: 32, mmio: 0xfeaffc00
[   37.568857] saa7134[0]: subsystem: 1894:a006, board: KNC One TV-Station DVR [card=24,autodetected]
[   37.568870] saa7134[0]: board init: gpio is 830000
[   37.703903] saa7134[0]: i2c eeprom 00: 94 18 06 a0 06 80 00 01 00 00 00 00 00 00 01 00
[   37.703924] saa7134[0]: i2c eeprom 10: 00 ff 86 0e ff 20 ff ff ff ff ff ff ff ff ff ff
[   37.703943] saa7134[0]: i2c eeprom 20: 01 40 01 02 02 03 01 03 06 ff 01 df ff ff ff ff
[   37.703962] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   37.703981] saa7134[0]: i2c eeprom 40: ff 05 00 c0 86 ff ff ff ff ff ff ff ff ff ff ff
[   37.704001] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   37.704020] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   37.704039] saa7134[0]: i2c eeprom 70: 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[   37.779764] tuner 0-0043: chip found @ 0x86 (saa7134[0])
[   37.779798] tda9887 0-0043: tda988[5/6/7] found @ 0x43 (tuner)
[   37.795736] tuner 0-0060: All bytes are equal. It is not a TEA5767
[   37.795742] tuner 0-0060: chip found @ 0xc0 (saa7134[0])
[   37.795777] tuner 0-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[   37.795781] tuner 0-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[   37.831710] saa6752hs 0-0020: saa6752hs: chip found @ 0x40
[   37.831946] saa7134[0]: registered device video0 [v4l2]
[   37.832030] saa7134[0]: registered device vbi0
[   37.832099] saa7134[0]: registered device radio0
[   37.843799] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 17
[   37.860749] saa7134 ALSA driver for DMA sound loaded
[   37.860940] saa7134[0]/alsa: saa7134[0] at 0xfeaffc00 irq 20 registered as card -2
[   37.945816] saa7134[0]: registered device video1 [mpeg]
[   38.565556] lp0: using parport0 (interrupt-driven).
[   38.622265] Adding 996020k swap on /dev/sda2.  Priority:-1 extents:1 across:996020k
[   38.970533] EXT3 FS on sda1, internal journal
[   39.791880] kjournald starting.  Commit interval 5 seconds
[   39.792134] EXT3 FS on sda3, internal journal
[   39.792140] EXT3-fs: mounted filesystem with ordered data mode.

[ilin]

Kartę i tuner juz znamy.

Pokaż jeszcze wynik polecenia

Kod: Zaznacz cały

arecord -l

[EloElo]

Kod: Zaznacz cały

**** Lista CAPTURE urządzeń ****
karta 0: CMI8738 [C-Media PCI CMI8738], urządzenie 0: CMI8738 [C-Media PCI DAC/ADC]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 0: CMI8738 [C-Media PCI CMI8738], urządzenie 2: CMI8738 [C-Media PCI IEC958]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 1: SAA7134 [SAA7134], urządzenie 0: SAA7134 PCM [SAA7134 PCM]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0

[ilin]

Sprobuj odpalic takim poleceniem

Kod: Zaznacz cały

arecord -D hw:1,0 -r 32000 -c 2 -f S16_LE | aplay - & tvtime -d /dev/video0 && killall arecord

[EloElo]

no jest postęp bo jest "brynczenie/żężolenie" ale na wszystkich kanalach takie samo

[ilin]

Wpisz sobie do plików
/etc/modules

Kod: Zaznacz cały

saa7134-alsa

/etc/modprobe.d/aliases

Kod: Zaznacz cały

alias char-major-81 videodev
alias char-major-81-0 saa7134
options saa7134 card=24 tuner=38

Restart i odpal znów powyzszym poleceniem

[EloElo]

nadal to samo...

Kod: Zaznacz cały

[1] 1507
Uruchomione tvtime 1.0.2.
Nagrywanie WAVE 'stdin' : Signed 16 bit Little Endian, Częstotliwość 32000 Hz, Stereo
Odtwarzanie WAVE 'stdin' : Signed 16 bit Little Endian, Częstotliwość 32000 Hz, Stereo
Czytanie konfiguracji z /etc/tvtime/tvtime.xml
I/O warning : failed to load external entity "/home/jacek/.tvtime/tvtime.xml"
I/O error : Permission denied
I/O error : Permission denied
Nie można zmienić właściciela /home/jacek/.tvtime/tvtime.xml: Permission denied.
I/O error : Permission denied
I/O error : Permission denied
arecord: pcm_read:1346: błąd odczytu: Input/output error
I/O error : Permission denied
I/O error : Permission denied
I/O error : Permission denied
I/O error : Permission denied

[andrzej244]

Może to pomoże -mój stary post...do Mandriva
Z tego co pamiętam to na ubuntu 7.10 śmigała mi ta karta super(bez kabelka nie dałem rady uruchomić dźwięku).

http://www.mandrivaclub.pl/forum/medion ... 11036.html
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------

EDIT:
Do karty saa7134 należy dokupić kabelek audio (na allegro za 1zł + koszty przesyłki) i podłączyć jeden koniec do wejścia AUX va płycie głównaj(Też powinno działać gdy podepniemy do CD IN) a drugi do białego gniazda karty TV.
Pomocna strona: http://www.elektroda.pl/rtvforum/topic777244.html
Doinstalować programy kdetv i tvtime.

Własnie uruchomiłem kartę saa7134 na ubuntu 8.04 - oczywiscie dźwięk przez kabelek audio.
Chodzi dobrze. W regulacji głośności trzeba dodać suwak AUX, włączyć go i podgłóśnić.
Tv u mnie działa na programach kdetv i tvtime.

[alek666]

mam analogiczny problem. nie mam dzwieku przy ogladaniu tv. poza tym wszystko dziala super.
ilin mi swoim postem troche pomogl, ale to nie jest rozwiazanie, wiec bym byl wdzieczny gdyby mi jeszcze ktos dopomogl.
moja karta telewizyjna:

Kod: Zaznacz cały

02:02.0 Multimedia controller: Philips Semiconductors SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)

podobno to Medion oparty na Philipsie - zreszta widac
caly dzien dzis spedzilem na poszukiwaniach znalezienia rozwiazania mojego problemu. ale wysilki spelzy na niczym.
az do teraz. otoz po wstukaniu:

Kod: Zaznacz cały

arecord -D hw:1,0 -r 32000 -c 2 -f S16_LE | aplay - & tvtime -d /dev/video0 && killall arecord

dzwiek mi sie pojawil.
no, ale po paru minutach dzwiek z obrazem sie rozkrzacza, co nie dziwi jesli to zdaje sie, ze jest "wtornie odgrywane"

Kod: Zaznacz cały

alek@kompoziomka:~$ arecord -l
**** Lista CAPTURE urządzeń ****
karta 0: ICH5 [Intel ICH5], urządzenie 0: Intel ICH [Intel ICH5]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 0: ICH5 [Intel ICH5], urządzenie 1: Intel ICH - MIC ADC [Intel ICH5 - MIC ADC]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 0: ICH5 [Intel ICH5], urządzenie 2: Intel ICH - MIC2 ADC [Intel ICH5 - MIC2 ADC]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 0: ICH5 [Intel ICH5], urządzenie 3: Intel ICH - ADC2 [Intel ICH5 - ADC2]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0
karta 1: SAA7134 [SAA7134], urządzenie 0: SAA7134 PCM [SAA7134 PCM]
  Urządzenia podrzędne: 1/1
  Urządzenie podrzędne #0: subdevice #0

czy tylko kabelek tutaj mnie uratuje? pod windowsem jest dzwiek, no ale jakosc gorsza, programy do... niczego, itp niewygody
bede wdzieczny za jakiekolwiek rady.

[ilin]

Spróbuj użyć zamiast arecord soxa.
http://404.g-net.pl/?p=98

Daj znać jak to działa bo sam jestem ciekaw.

[alek666]

niestety nic z tego nie wyjdzie, bo juz uzywalem tego; wyrzucalo mi to co pod spodem:

Kod: Zaznacz cały

sox -r 32000 -w -t alsa hw:1,0 -t alsa hw:0,0
sox soxio: Failed reading `hw:1,0': unknown file type `alsa'

arecord -D hw:1,0 -r 32000 -c 2 -f S16_LE | sox -q -c 2 -r 32000 -w -t wav - -t alsa hw:0,0
sox soxio: Failed reading `-': unknown file type `wav'

sox -q -c 2 -s -w -r 32000 -t ossdsp /dev/dsp1 -t ossdsp -w -r 32000 /dev/dsp
sox soxio: Failed reading `/dev/dsp1': unknown file type `ossdsp'

poradzilem sobie tymczasowo inaczej:

Kod: Zaznacz cały

mplayer tv:// -tv alsa:adevice=hw.1,0:audiorate=32000:immediatemode=0

to jest minimalna ilosc opcji, z ktora jest dzwiek (i obraz) u mnie na mplayerze.
zmiana kanalow klawiszami h i k. i to jest tyle co do tej pory zrobilem od rana 8:45

[Golem_XIV]

Pomijając fakt, że nie masz uprawnień do odczytu:

Kod: Zaznacz cały

I/O warning : failed to load external entity "/home/jacek/.tvtime/tvtime.xml"

Taka wpadka z Tvtime, tworzy katalog .tvtime w katalogu użytkownika przypisany do roota. Rozwiązanie - albo zmienić uprawnienia do katalogu i plików w środku jako root, albo jako root usunąć katalog "/home/jacek/.tvtime/" i założyć go sobie z poziomu użytkownika. Po włączeniu tvtime sam sobie stworzy odpowiednie pliki i pewnie znów trzeba będzie poszukać kanałów.