TPLink WN-551g - zmiana trybu

[szopler]

Witam,
Dzisiaj przyszła do mnie karta jak w tytule... Po krótkich bojach zainstalowałem MadWifi i udało mi się zobaczyć kartę wśród interfejsów.

Kod: Zaznacz cały

root@x02-server:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

eth1      no wireless extensions.

wifi0     no wireless extensions.

ath0      IEEE 802.11g  ESSID:""  Nickname:""
          Mode:Managed  Frequency:2.437 GHz  Access Point: Not-Associated   
          Bit Rate:0 kb/s   Tx-Power=1 dBm   Sensitivity=1/1  
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/70  Signal level=-95 dBm  Noise level=-95 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

Kod: Zaznacz cały

root@x02-server:~# ifconfig
ath0      Link encap:Ethernet  HWaddr 00:1d:0f:b4:a8:06  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 00:0a:cd:00:a3:6f  
          inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::20a:cdff:fe00:a36f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:31312 errors:0 dropped:0 overruns:0 frame:0
          TX packets:24451 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:41480732 (39.5 MB)  TX bytes:2230781 (2.1 MB)
          Interrupt:19 Base address:0xb800 

eth1      Link encap:Ethernet  HWaddr 00:0c:6e:7a:fc:3a  
          inet addr:192.168.7.2  Bcast:192.168.7.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:6eff:fe7a:fc3a/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3246 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3025 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:432619 (422.4 KB)  TX bytes:1988218 (1.8 MB)
          Interrupt:20 Base address:0xb400 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:984 errors:0 dropped:0 overruns:0 frame:0
          TX packets:984 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:49200 (48.0 KB)  TX bytes:49200 (48.0 KB)

wifi0     Link encap:UNSPEC  HWaddr 00-1D-0F-B4-A8-06-00-00-00-00-00-00-00-00-00-00  
          inet addr:192.168.77.2  Bcast:192.168.77.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:435 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:199 
          RX bytes:0 (0.0 B)  TX bytes:20010 (19.5 KB)
          Interrupt:21

Jednak przy próbie:

Kod: Zaznacz cały

root@x02-server:~# iwconfig ath0 mode master
Error for wireless request "Set Mode" (8B06) :
    SET failed on device ath0 ; Invalid argument.

Także:

Kod: Zaznacz cały

root@x02-server:~# iwconfig ath0 mode ad-hoc
Error for wireless request "Set Mode" (8B06) :
    SET failed on device ath0 ; Invalid argument.

Chciałbym tą kartę uruchomić w trybie master jako AP domowy...

Na koniec jeszcze podam:

Kod: Zaznacz cały

root@x02-server:~# lspci
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02)
02:09.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
02:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

Co radzicie?

EDIT:
Sam sobie odpowiem... temat w zasadzie do zamknięcia / usunięcia...

Kod: Zaznacz cały

wlanconfig ath0 destroy
wlanconfig ath0 create wlandev wifi0 wlanmode ap

EoT