Nie wykrywa karty sieciowej

[melu]

aWIEC TAK. Zrobiłem sobie format i chciałem wrocic z slackware znow na ubuntu noi zaczolem konfigurowac neta tak jak to robilem zawsze DNS ip maske brame a tu NET ni działa. Posiadam radiówkę Pole Wartość
Karta sieciowa SiS 900-Based PCI Fast Ethernet Adapter


Wynik iwconfig*a

melu@melu-desktop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions

Nie rozumie jednego. Jeszcze 2 miesiące temu miałm neta a teraz nie. :/

[uszek2007]

Zrobiłem sobie format i chciałem wrocic z slackware znow na ubuntu noi zaczolem konfigurowac neta tak jak to robilem zawsze DNS ip maske brame a tu NET ni działa. Posiadam radiówkę Pole Wartość
Karta sieciowa SiS 900-Based PCI Fast Ethernet Adapter

daj lspci

[melu]

melu@melu-desktop:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 746 Host (rev 10)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 90)
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1)

Proszę

[uszek2007]

thernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet

to jest nie radiowa karta tylko Ethernet
jezeli by była karta wifi to była by zaznaczona jako
ath0 lub wifi0
zle coś skonfigurowałeś w ustawieniach sieci

EDIT:
wbudowana jest w płytę główna

[melu]

Kurcze no robie cały czas tak jak zawsze, ale dalej nie mam :/ . Prosze o pomoc.

[DadaD]

Kurcze no robie cały czas tak jak zawsze, ale dalej nie mam :/ . Prosze o pomoc.

Przed chwilą włączyłem laptop gdzie mam kartę wifi
polecenie
lspci
oraz dmesg
pokazało kartę?

Jaka Ty masz kartę wbudowaną pci czy usb?

Podaj ewentualnie wynik dotyczący kart jako root
lspci
dmesg
lsusb jeżeli to karta usb

Powyższe polecenia wydane jako user dały mi odpowiedź o mojej karcie!

Pozdrowienia

PS kolega uszek2007 ma rację to

00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 90)

jest zwykłą kartą sieciową ale nie wifi!

[melu]

Mam karte wbudowaną

lspci

melu@melu-desktop:~$ lspci
00:00.0 Host bridge: Smelu@melu-desktop:~$ lspciilicon Integrated Systems [SiS] 746 Host (rev 10)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 90)
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1)

EDIT:
dmesg

melu@melu-desktop:~$ dmesg
[ 0.000000] Linux version 2.6.24-16-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:23:42 UTC 2008 (Ubuntu 2.6.24-16.30-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000006fff0000 (usable)
[ 0.000000] BIOS-e820: 000000006fff0000 - 000000006fff8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000006fff8000 - 0000000070000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
[ 0.000000] 895MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 458736) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 458736
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 458736
[ 0.000000] On node 0 totalpages: 458736
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1791 pages used for memmap
[ 0.000000] HighMem zone: 227569 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FAB70 checksum 0
[ 0.000000] ACPI: RSDP 000FAB70, 0014 (r0 AMI )
[ 0.000000] ACPI: RSDT 6FFF0000, 002C (r1 AMIINT SiS740XX 1000 MSFT 100000B)
[ 0.000000] ACPI: FACP 6FFF0030, 0081 (r1 AMIINT SiS740XX 11 MSFT 100000B)
[ 0.000000] ACPI: DSDT 6FFF0120, 32B4 (r1 SiS 746 100 MSFT 100000D)
[ 0.000000] ACPI: FACS 6FFF8000, 0040
[ 0.000000] ACPI: APIC 6FFF00C0, 005A (r1 AMIINT SiS740XX 1000 MSFT 100000B)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 70000000:8ec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 455153
[ 0.000000] Kernel command line: root=UUID=7d012301-d8b3-49d9-ae0d-8f15de77ffe0 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1999.954 MHz processor.
[ 17.008892] Console: colour VGA+ 80x25
[ 17.008897] console [tty0] enabled
[ 17.009794] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 17.011699] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.119583] Memory: 1806752k/1834944k available (2157k kernel code, 26956k reserved, 998k data, 364k init, 917440k highmem)
[ 17.119593] virtual kernel memory layout:
[ 17.119594] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 17.119595] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 17.119596] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 17.119598] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 17.119599] .init : 0xc041b000 - 0xc0476000 ( 364 kB)
[ 17.119600] .data : 0xc031b5a4 - 0xc0414dc4 ( 998 kB)
[ 17.119601] .text : 0xc0100000 - 0xc031b5a4 (2157 kB)
[ 17.119605] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 17.119672] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 17.199697] Calibrating delay using timer specific routine.. 4002.11 BogoMIPS (lpj=8004232)
[ 17.199748] Security Framework initialized
[ 17.199759] SELinux: Disabled at boot.
[ 17.199792] AppArmor: AppArmor initialized
[ 17.199798] Failure registering capabilities with primary security module.
[ 17.199812] Mount-cache hash table entries: 512
[ 17.200024] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 00000000
[ 17.200036] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 17.200039] CPU: L2 Cache: 256K (64 bytes/line)
[ 17.200043] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 00000000
[ 17.200057] Compat vDSO mapped to ffffe000.
[ 17.200076] Checking 'hlt' instruction... OK.
[ 17.216015] SMP alternatives: switching to UP code
[ 17.217367] Freeing SMP alternatives: 11k freed
[ 17.217543] Early unpacking initramfs... done
[ 17.585378] ACPI: Core revision 20070126
[ 17.585492] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 17.587020] CPU0: AMD Athlon(tm) XP 2400+ stepping 01
[ 17.587048] Total of 1 processors activated (4002.11 BogoMIPS).
[ 17.587153] ENABLING IO-APIC IRQs
[ 17.587333] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 17.731799] Brought up 1 CPUs
[ 17.731837] CPU0 attaching sched-domain:
[ 17.731840] domain 0: span 01
[ 17.731842] groups: 01
[ 17.732105] net_namespace: 64 bytes
[ 17.732116] Booting paravirtualized kernel on bare hardware
[ 17.732638] Time: 9:12:26 Date: 01/02/09
[ 17.732684] NET: Registered protocol family 16
[ 17.732944] EISA bus registered
[ 17.732968] ACPI: bus type pci registered
[ 17.734801] PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
[ 17.734805] PCI: Using configuration type 1
[ 17.734806] Setting up standard PCI resources
[ 17.736900] ACPI: EC: Look up EC in DSDT
[ 17.739807] ACPI: Interpreter enabled
[ 17.739811] ACPI: (supports S0 S1 S4 S5)
[ 17.739825] ACPI: Using IOAPIC for interrupt routing
[ 17.743666] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 17.743873] Enabling SiS 96x SMBus.
[ 17.744374] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 17.752357] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 17.752452] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 17.752537] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 17.752624] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 17.752708] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 17.752794] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 17.752880] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 17.752966] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 17.753076] ACPI: Power Resource [URP1] (off)
[ 17.753101] ACPI: Power Resource [URP2] (off)
[ 17.753127] ACPI: Power Resource [FDDP] (off)
[ 17.753152] ACPI: Power Resource [LPTP] (off)
[ 17.753208] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 17.753249] pnp: PnP ACPI init
[ 17.753259] ACPI: bus type pnp registered
[ 17.755722] pnp: PnP ACPI: found 11 devices
[ 17.755725] ACPI: ACPI bus type pnp unregistered
[ 17.755748] PnPBIOS: Disabled by ACPI PNP
[ 17.756049] PCI: Using ACPI for IRQ routing
[ 17.756054] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 17.767775] NET: Registered protocol family 8
[ 17.767778] NET: Registered protocol family 20
[ 17.767883] AppArmor: AppArmor Filesystem Enabled
[ 17.771730] Time: tsc clocksource has been installed.
[ 17.779775] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 17.779778] system 00:01: ioport range 0x295-0x296 has been reserved
[ 17.779781] system 00:01: ioport range 0x800-0x87f has been reserved
[ 17.779784] system 00:01: ioport range 0x880-0x8ff has been reserved
[ 17.779787] system 00:01: ioport range 0xc00-0xc1f has been reserved
[ 17.779791] system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 17.810310] PCI: Bridge: 0000:00:01.0
[ 17.810312] IO window: disabled.
[ 17.810319] MEM window: cdd00000-cfefffff
[ 17.810323] PREFETCH window: bda00000-cdbfffff
[ 17.810353] NET: Registered protocol family 2
[ 17.847859] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 17.848319] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 17.850555] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 17.851665] TCP: Hash tables configured (established 131072 bind 65536)
[ 17.851670] TCP reno registered
[ 17.859946] checking if image is initramfs... it is
[ 18.311770] Switched to high resolution mode on CPU 0
[ 18.535240] Freeing initrd memory: 7703k freed
[ 18.536157] audit: initializing netlink socket (disabled)
[ 18.536180] audit(1230887547.312:1): initialized
[ 18.536446] highmem bounce pool size: 64 pages
[ 18.538579] VFS: Disk quotas dquot_6.5.1
[ 18.538676] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 18.538853] io scheduler noop registered
[ 18.538856] io scheduler antiCEBULKAtory registered
[ 18.538858] io scheduler deadline registered
[ 18.538869] io scheduler cfq registered (default)
[ 18.538931] Boot video device is 0000:01:00.0
[ 18.539282] isapnp: Scanning for PnP cards...
[ 18.892727] isapnp: No Plug & Play device found
[ 18.925374] Real Time Clock Driver v1.12ac
[ 18.925502] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 18.925644] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 18.926458] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 18.927406] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 18.927492] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 18.927619] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 18.927622] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp

[melu]

Musiałem to podzielic bo nie chciało odp

[ 18.927777] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.935810] mice: PS/2 mouse device common for all mice
[ 18.935958] EISA: Probing bus 0 at eisa.0
[ 18.935995] EISA: Detected 0 cards.
[ 18.936000] cpuidle: using governor ladder
[ 18.936003] cpuidle: using governor menu
[ 18.936185] NET: Registered protocol family 1
[ 18.936225] Using IPI No-Shortcut mode
[ 18.936275] registered taskstats version 1
[ 18.936379] Magic number: 9:238:221
[ 18.936455] hash matches device ttyu5
[ 18.936657] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 18.936659] EDD information not available.
[ 18.937252] Freeing unused kernel memory: 364k freed
[ 18.963718] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 20.237566] fuse init (API version 7.9)
[ 20.951049] SCSI subsystem initialized
[ 21.026069] libata version 3.00 loaded.
[ 21.042428] usbcore: registered new interface driver usbfs
[ 21.042464] usbcore: registered new interface driver hub
[ 21.055562] usbcore: registered new device driver usb
[ 21.056539] sis900.c: v1.08.10 Apr. 2 2006
[ 21.056645] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 21.057552] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[ 21.066591] 0000:00:04.0: Using transceiver found at address 1 as default
[ 21.069923] eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 16, 00:0b:6a:56:36:b6
[ 21.080270] pata_sis 0000:00:02.5: version 0.5.2
[ 21.091529] scsi0 : pata_sis
[ 21.096317] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.119499] scsi1 : pata_sis
[ 21.120164] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[ 21.120168] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[ 21.179678] Floppy drive(s): fd0 is 1.44M
[ 21.203262] FDC 0 is a post-1991 82077
[ 21.283849] ata1.00: ATA-7: SAMSUNG SP0802N, TK100-24, max UDMA/100
[ 21.283857] ata1.00: 156368016 sectors, multi 16: LBA48
[ 21.291887] ata1.00: configured for UDMA/100
[ 21.767853] ata2.00: ATAPI: HL-DT-ST GCE-8525B, 1.03, max UDMA/33
[ 21.767877] ata2.01: ATAPI: HL-DT-STDVD-ROM GDR8163B, 0L14, max UDMA/33
[ 21.931828] ata2.00: configured for UDMA/33
[ 22.103624] ata2.01: configured for UDMA/33
[ 22.103826] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP0802N TK10 PQ: 0 ANSI: 5
[ 22.104669] scsi 1:0:0:0: CD-ROM HL-DT-ST CD-RW GCE-8525B 1.03 PQ: 0 ANSI: 5
[ 22.107936] scsi 1:0:1:0: CD-ROM HL-DT-ST DVD-ROM GDR8163B 0L14 PQ: 0 ANSI: 5
[ 22.110331] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 17
[ 22.110355] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 22.110819] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 22.110849] ohci_hcd 0000:00:03.0: irq 17, io mem 0xcfffd000
[ 22.165580] usb usb1: configuration #1 chosen from 1 choice
[ 22.165617] hub 1-0:1.0: USB hub found
[ 22.165629] hub 1-0:1.0: 3 ports detected
[ 22.267561] ACPI: PCI Interrupt 0000:00:03.1 -> GSI 21 (level, low) -> IRQ 18
[ 22.267588] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 22.267622] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 22.267645] ohci_hcd 0000:00:03.1: irq 18, io mem 0xcfffe000
[ 22.325535] usb usb2: configuration #1 chosen from 1 choice
[ 22.325572] hub 2-0:1.0: USB hub found
[ 22.325584] hub 2-0:1.0: 3 ports detected
[ 22.428092] ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) -> IRQ 19
[ 22.428118] ehci_hcd 0000:00:03.2: EHCI Host Controller
[ 22.428160] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 22.428213] PCI: cache line size of 64 is not supported by device 0000:00:03.2
[ 22.428228] ehci_hcd 0000:00:03.2: irq 19, io mem 0xcffff000
[ 22.571359] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 22.583363] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 22.583544] usb usb3: configuration #1 chosen from 1 choice
[ 22.583577] hub 3-0:1.0: USB hub found
[ 22.583586] hub 3-0:1.0: 6 ports detected
[ 22.703309] Driver 'sd' needs updating - please use bus_type methods
[ 22.703580] sd 0:0:0:0: [sda] 156368016 512-byte hardware sectors (80060 MB)
[ 22.703599] sd 0:0:0:0: [sda] Write Protect is off
[ 22.703603] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.703623] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.703689] sd 0:0:0:0: [sda] 156368016 512-byte hardware sectors (80060 MB)
[ 22.703701] sd 0:0:0:0: [sda] Write Protect is off
[ 22.703704] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.703721] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.703726] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 22.719538] sda1 sda2 < sda5 sda6 > sda3 sda4
[ 22.762703] sd 0:0:0:0: [sda] Attached SCSI disk
[ 22.772427] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 22.772454] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 22.772476] scsi 1:0:1:0: Attached scsi generic sg2 type 5
[ 22.772866] sr0: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
[ 22.772873] Uniform CD-ROM driver Revision: 3.20
[ 22.772927] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 22.789365] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 22.789470] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 23.319316] usb 3-3: new high speed USB device using ehci_hcd and address 3
[ 23.416222] Attempting manual resume
[ 23.416229] swsusp: Resume From Partition 8:3
[ 23.416231] PM: Checking swsusp image.
[ 23.416509] PM: Resume from disk failed.
[ 23.435113] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 23.435121] EXT3-fs: write access will be enabled during recovery.
[ 23.454778] kjournald starting. Commit interval 5 seconds
[ 23.454800] EXT3-fs: recovery complete.
[ 23.454946] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.461405] usb 3-3: configuration #1 chosen from 1 choice
[ 23.763273] usb 2-1: new low speed USB device using ohci_hcd and address 2
[ 23.976334] usb 2-1: configuration #1 chosen from 1 choice
[ 23.982454] usbcore: registered new interface driver libusual
[ 24.184589] Initializing USB Mass Storage driver...
[ 24.184700] scsi2 : SCSI emulation for USB Mass Storage devices
[ 24.184795] usbcore: registered new interface driver usb-storage
[ 24.184800] USB Mass Storage support registered.
[ 24.185925] usb-storage: device found at 3
[ 24.185927] usb-storage: waiting for device to settle before scanning
[ 29.183208] usb-storage: device scan complete
[ 29.184321] scsi 2:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS
[ 29.186148] sd 2:0:0:0: [sdb] 1955840 512-byte hardware sectors (1001 MB)
[ 29.186772] sd 2:0:0:0: [sdb] Write Protect is off
[ 29.186775] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 29.186779] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 29.190145] sd 2:0:0:0: [sdb] 1955840 512-byte hardware sectors (1001 MB)
[ 29.190770] sd 2:0:0:0: [sdb] Write Protect is off
[ 29.190773] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 29.190775] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 29.190779] sdb: sdb1
[ 29.192106] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 29.192146] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 30.978742] Linux agpgart interface v0.102
[ 31.034907] agpgart: Detected SiS chipset - id:1862
[ 31.040564] agpgart: AGP aperture is 64M @ 0xd0000000
[ 31.110790] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 31.182920] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 31.478847] input: Power Button (FF) as /devices/virtual/input/input2
[ 31.494649] ACPI: Power Button (FF) [PWRF]
[ 31.494785] input: Power Button (CM) as /devices/virtual/input/input3
[ 31.510826] ACPI: Power Button (CM) [PWRB]
[ 31.539986] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
[ 33.214772] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 20
[ 33.451499] usbcore: registered new interface driver hiddev
[ 33.458936] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:03.1/usb2/2-1/2-1:1.0/input/input4
[ 33.482937] input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:03.1-1
[ 33.482971] usbcore: registered new interface driver usbhid
[ 33.482976] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 33.538491] intel8x0_measure_ac97_clock: measured 55772 usecs
[ 33.538498] intel8x0: clocking to 48000
[ 33.706013] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 34.264093] parport_pc 00:09: reported by Plug and Play ACPI
[ 34.264196] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 35.715193] eth0: Media Link On 100mbps full-duplex
[ 37.017130] lp0: using parport0 (interrupt-driven).
[ 37.095572] Adding 1437808k swap on /dev/sda3. Priority:-1 extents:1 across:1437808k
[ 37.663494] EXT3 FS on sda6, internal journal
[ 38.475415] kjournald starting. Commit interval 5 seconds
[ 38.475557] EXT3 FS on sda4, internal journal
[ 38.475564] EXT3-fs: mounted filesystem with ordered data mode.
[ 38.999720] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 39.556833] No dock devices found.
[ 40.829489] apm: BIOS not found.
[ 40.958073] ppdev: user-space parallel port driver
[ 41.089381] audit(1230883970.189:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4804 profile="/usr/sbin/cupsd" namespace="default"
[ 42.428079] Bluetooth: Core ver 2.11
[ 42.429431] NET: Registered protocol family 31
[ 42.429440] Bluetooth: HCI device and connection manager initialized
[ 42.429446] Bluetooth: HCI socket layer initialized
[ 42.477926] Bluetooth: L2CA
P ver 2.9
[ 42.477935] Bluetooth: L2CAP socket layer initialized
[ 42.578607] Bluetooth: RFCOMM socket layer initialized
[ 42.579294] Bluetooth: RFCOMM TTY layer initialized
[ 42.579298] Bluetooth: RFCOMM ver 1.8
[ 66.072905] NET: Registered protocol family 10
[ 66.074307] lo: Disabled Privacy Extensions
[ 76.079088] eth0: no IPv6 routers present

[DadaD]

Mam karte wbudowaną

Wyniki poleceń nie zawierają informacji o karcie wifi.

podaj wynik polecenia

Kod: Zaznacz cały

lshw

ale najpierw sprawdź czy karta jest sprzętowo włączona. Należy nacisnąć przycisk na laptopie! Myślę że to rozwiąże problem.

Pozdrowienia

[melu]

yyyyyyyyyy wynikło jakiej nieporozumienie. Ja nie mam laptopa !! Tylko stacionarny i kablówkę

Pomuż ktoś :/


Robię nawet tak jak tu viewtopic.php?t=41238 ale nic. Juz mnie to powoli wkur***. Dawniej robiłem tak samo i było. Jedno jest dziwnego teraz jak zeby dowiedziec sie jakie DNS*y sa do wbijam w konsoli ipconfig /all i Pisze tylko jeden serwer DNS nandodatek taki sam jak brama.

[DadaD]

Wynik iwconfig*a

Kod: Zaznacz cały

melu@melu-desktop:~$ iwconfig
lo no wireless extensions.

eth0 no wireless extensions 

Nie rozumie jednego. Jeszcze 2 miesiące temu miałm neta a teraz nie. :/

Powyższy wynik podaje brak karty wifi lub że nie jest skonfigurowana!

Załączony poniższy wynik polecenia pokazuje brak karty wifi!!!!!!

Kod: Zaznacz cały

melu@melu-desktop:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 746 Host (rev 10)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 90)
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev c1) 

natomiast jest widoczna karta przewodowa!

Otwórz komputer i zobacz czy karta wifi jest w slocie.

nie podałeś wyniku o co Ciebie prosiłem lshw

A może internet masz dostarczany drogą radiową do routera i od niego idzie kabelek do karty sieciowej w komputerze?

Pozdrowienia

Ja się gubię raz używasz poleceń do konfiguracji karty wifi iwconfig a później podajesz linki do karty ethernet i polecenia jej dotyczące ifconfigviewtopic.php?t=41238

Określ o jaką kartę chodzi!!

[melu]

A może internet masz dostarczany drogą radiową do routera i od niego idzie kabelek do karty sieciowej w komputerze?

O to mi własnie chodziło.
Z tym iwconfig sorry troche sie zamotałem. Mam nadzieje że teraz wszystko jasne.


lshw

melu@melu-desktop:~$ lshw
WARNING: you should run this program as super-user.
melu-desktop
description: Computer
width: 32 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 0
size: 1773MiB
*-cpu
product: AMD Athlon(tm) XP 2400+
vendor: Advanced Micro Devices [AMD]
physical id: 1
bus info: cpu@0
version: 6.8.1
size: 2GHz
width: 32 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow up ts
*-cache:0
description: L1 cache
physical id: 0
size: 128KiB
*-cache:1
description: L2 cache
physical id: 1
size: 256KiB
*-pci
description: Host bridge
product: 746 Host
vendor: Silicon Integrated Systems [SiS]
physical id: 100
bus info: pci@0000:00:00.0
version: 10
width: 32 bits
clock: 33MHz
configuration: driver=agpgart-sis module=sis_agp
*-pci
description: PCI bridge
product: SG86C202
vendor: Silicon Integrated Systems [SiS]
physical id: 1
bus info: pci@0000:00:01.0
version: 00
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master
*-display UNCLAIMED
description: VGA compatible controller
product: NV18 [GeForce4 MX 440 AGP 8x]
vendor: nVidia Corporation
physical id: 0
bus info: pci@0000:01:00.0
version: c1
width: 32 bits
clock: 66MHz
capabilities: vga_controller bus_master cap_list
configuration: latency=32 maxlatency=1 mingnt=5
*-isa
description: ISA bridge
product: SiS963 [MuTIOL Media IO]
vendor: Silicon Integrated Systems [SiS]
physical id: 2
bus info: pci@0000:00:02.0
version: 25
width: 32 bits
clock: 33MHz
capabilities: isa bus_master
configuration: latency=0
*-serial
description: SMBus
product: SiS961/2 SMBus Controller
vendor: Silicon Integrated Systems [SiS]
physical id: 2.1
bus info: pci@0000:00:02.1
version: 00
width: 32 bits
clock: 33MHz
configuration: driver=sis96x_smbus latency=0 module=i2c_sis96x
*-ide
description: IDE interface
product: 5513 [IDE]
vendor: Silicon Integrated Systems [SiS]
physical id: 2.5
bus info: pci@0000:00:02.5
version: 00
width: 32 bits
clock: 33MHz
capabilities: ide bus_master
configuration: driver=pata_sis latency=128 module=pata_sis
*-multimedia
description: Multimedia audio controller
product: AC'97 Sound Controller
vendor: Silicon Integrated Systems [SiS]
physical id: 2.7
bus info: pci@0000:00:02.7
version: a0
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list
configuration: driver=Intel ICH latency=32 maxlatency=11 mingnt=52 module=snd_intel8x0
*-usb:0
description: USB Controller
product: USB 1.1 Controller
vendor: Silicon Integrated Systems [SiS]
physical id: 3
bus info: pci@0000:00:03.0
version: 0f
width: 32 bits
clock: 33MHz
capabilities: ohci bus_master
configuration: driver=ohci_hcd latency=32 maxlatency=80 module=ohci_hcd
*-usb:1
description: USB Controller
product: USB 1.1 Controller
vendor: Silicon Integrated Systems [SiS]
physical id: 3.1
bus info: pci@0000:00:03.1
version: 0f
width: 32 bits
clock: 33MHz
capabilities: ohci bus_master
configuration: driver=ohci_hcd latency=32 maxlatency=80 module=ohci_hcd
*-usb:2
description: USB Controller
product: USB 2.0 Controller
vendor: Silicon Integrated Systems [SiS]
physical id: 3.2
bus info: pci@0000:00:03.2
version: 00
width: 32 bits
clock: 33MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd latency=32 maxlatency=80 module=ehci_hcd
*-network
description: Ethernet interface
product: SiS900 PCI Fast Ethernet
vendor: Silicon Integrated Systems [SiS]
physical id: 4
bus info: pci@0000:00:04.0
logical name: eth0
version: 90
serial: 00:0b:6a:56:36:b6
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=sis900 driverversion=v1.08.10 Apr. 2 2006 ip=192.168.1.234 latency=32 maxlatency=11 mingnt=52 module=sis900 multicast=yes
*-scsi
physical id: 1
bus info: scsi@2
logical name: scsi2
capabilities: scsi-host
configuration: driver=usb-storage
melu@melu-desktop:~$
melu@melu-desktop:~$

[DadaD]

O to mi własnie chodziło.
Z tym iwconfig sorry troche sie zamotałem. Mam nadzieje że teraz wszystko jasne.

podaj wynik

Kod: Zaznacz cały

ifconfig

[uszek2007]

włącz kartę sieciową w biosie bo ona jest wyłaczona . i pomoże pewnie przy instalacji jak ustawiałeś bootowanie to wyłaczyłeś przez pomyłkę lub zresetowałeś bios
ubuntu widzi tą karte w lspci ona po instalacji ubuntu wykrywana jest automatycznie i w przypadku innego linux
ale ona jest wyłaczona i dlatego nie ma internetu innej opcji nie ma.

[melu]

lap...

melu@melu-desktop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:0b:6a:56:36:b6
inet addr:192.168.1.234 Bcast:192.168.1.235 Mask:255.255.255.252
inet6 addr: fe80::20b:6aff:fe56:36b6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:164 errors:0 dropped:0 overruns:0 frame:0
TX packets:36 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:11605 (11.3 KB) TX bytes:4657 (4.5 KB)
Interrupt:16 Base address:0xd400

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:884 errors:0 dropped:0 overruns:0 frame:0
TX packets:884 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:44200 (43.1 KB) TX bytes:44200 (43.1 KB)

[DadaD]

lap...

masz przydzielony adres

Kod: Zaznacz cały

inet addr:192.168.1.234

karta wysyła i odbiera pakiety

Kod: Zaznacz cały

RX packets:164 errors:0 dropped:0 overruns:0 frame:0
TX packets:36 errors:0 dropped:0 overruns:0 carrier:0

bez błędów.

Co Ci nie działa www, poczta, komunikatory?
Może masz blokadę w firewallu?

A co mówi

Kod: Zaznacz cały

ping www.wp.pl

Kod: Zaznacz cały

ping www.google.com

Kod: Zaznacz cały

ping 192.168.1.1 

Jeżeli używasz Windows i internet działa zobacz jakie wyniki masz po podaniu polecenia

Kod: Zaznacz cały

Uruchom -> cmd -> ipconfig /all

Czy takie same IP broadcast chodzi o to

Kod: Zaznacz cały

inet addr:192.168.1.234 Bcast:192.168.1.235 Mask:255.255.255.252

jak pod Ubuntu?

Sprawdź w dokumentacji od providera czy na routerze nie masz blokady numeru mac, czasem do routera jest przypisany jeden niezmienny numer MAC to ten

Kod: Zaznacz cały

eth0 Link encap:Ethernet HWaddr 00:0b:6a:56:36:b6 

pogrubiony

[melu]

Sorry ze nie odp, ale problemy techniczne. Ja tez sie dziwie ze nie mam neta bo zawsze tak konfigurowalem go i był a teraz nic. . kurcze dzis nie dam rady nic sprawdzic, bo na kompie wyjatkowo 1 min dzis jutro podam wyniki wsyztskiego .

EDIT:

Co Ci nie działa www, poczta, komunikatory?
Może masz blokadę w firewallu?

Nie działa ani str ani komunikator blokady nie mam.

A co mówi
Kod:
ping http://www.wp.pl
Kod:
ping http://www.google.com
Kod:
ping 192.168.1.1

Oto wyniki:

root@melu-desktop:/home/melu# ping http://www.google.com
ping: unknown host http://www.google.com

root@melu-desktop:/home/melu# ping http://www.google.com
ping: unknown host http://www.google.com

Czy takie same IP broadcast chodzi o to
Kod:
inet addr:192.168.1.234 Bcast:192.168.1.235 Mask:255.255.255.252

No jak konfigurowałme internet to to wpisałem ip i maske, ale Bcast nie bo tam nie było pola w ktorym mam to wpisać. Dawałem zreszta jak zawsze Static IP i uzupełniłem ip maske i brame i dodałem DNS*y i to tyle. [/quote]



Blokady nie ma zadnej

[DadaD]

No jak konfigurowałme internet to to wpisałem ip i maske, ale Bcast nie bo tam nie było pola w ktorym mam to wpisać. Dawałem zreszta jak zawsze Static IP i uzupełniłem ip maske i brame i dodałem DNS*y i to tyle.

a tu

ping 192.168.1.1

jak odpowiedziało

Edit:
W instrukcji od providera masz stałe IP i maskę ?
tzn. IP = 192.168.1.234 Mask:255.255.255.252
Czy też router przydziela numery z dhcp?

[melu]

Tak mam stałem IP
ping 192.168.1.1

melu@melu-desktop:~$ ping 192.168.1.1
connect: Network is unreachable
melu@melu-desktop:~$

[DadaD]

Tak mam stałem IP
ping 192.168.1.1

Zaraz powinniśmy rozwiązać problem.
Sprawdź ponownie wszystkie wpisane parametry i ewentualnie popraw
IP
Maska
Adres bramy czasem provider podaje inny niż domyślny!
DNS-y
oraz zobacz co mówi

route -n

jeżeli używasz jeszcze inny komputer podpięty do tego routera, lub Windows i sieć na nim dobrze działa porównaj konfigurację, czy nie ma błędu.

Sprawdź w pliku /etc/resolv.conf
poprawność wpisanych DNS-ów

Gdy dokonasz zmian na wszelki wypadek zrestartuj komputer

Sieć powinna działać

Sprawdż ping na adres zewnętrzny np.

ping 217.77.100.101
i ping na prawidłową bramę

Jeżeli jeszcze będzie problem
Aby jednorazowo ustawić interfejs - nie zapiszą się trwale znikną po restarcie. Wykonaj poniższe polecenia:
Oczywiście sprawdź poprawność!

Jako root

Kod: Zaznacz cały

ifconfig eth0 down; ifconfig eth0 hw ether 00:0b:6a:56:36:b6

Podnoszenie interfejsu

Kod: Zaznacz cały

ifconfig ethX 192.168.1.234 netmask 255.255.255.252 broadcast 192.168.1.235 up

Wyznaczenie bramy

Kod: Zaznacz cały

route add default gw 192.168.1.1

Ustawienie DNS-ów

Kod: Zaznacz cały

echo -e "nameserver ???.???.???.??? \nnamerserver ???.???.???.??" > /etc/resolv.conf

W miejsce ??? podaj prawidłowe wartości dla pierwszego i zapasowego

Tu masz podstawy teorii o konfiguracji

viewtopic.php?t=41238

Pozdrowienia