"Error found while checking desk drive for / "
Poczytałem trochę i prawdopodobnie mam uszkodzony dysk. Sprawdziłem smart Tool i mam 71 błędnych sektorów. Dysk 250 GB partycja ext 4. Tylko linux.
Wykonałem
Kod: Zaznacz cały
sudo smartctl -a /dev/sda1Kod: Zaznacz cały
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.4
Device Model: ST9250827AS
Serial Number: 5RG2B4G4
LU WWN Device Id: 5 000c50 00df22fa4
Firmware Version: 3.AAA
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Aug 22 20:52:57 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 120) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 426) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SCT capabilities: (0x0001) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 253 006 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 078 078 020 Old_age Always - 23004
5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 60
7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 4765755008
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 14573
10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 096 096 020 Old_age Always - 4177
187 Reported_Uncorrect 0x0032 065 065 000 Old_age Always - 35
189 High_Fly_Writes 0x003a 074 074 000 Old_age Always - 26
190 Airflow_Temperature_Cel 0x0022 060 036 045 Old_age Always In_the_past 40 (0 13 64 11)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 974
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 2459
193 Load_Cycle_Count 0x0022 001 001 000 Old_age Always - 281900
194 Temperature_Celsius 0x001a 040 064 000 Old_age Always - 40 (0 11 0 0)
195 Hardware_ECC_Recovered 0x0012 064 058 000 Old_age Always - 52411363
197 Current_Pending_Sector 0x0010 100 100 000 Old_age Offline - 11
198 Offline_Uncorrectable 0x003e 100 100 000 Old_age Always - 11
199 UDMA_CRC_Error_Count 0x0000 200 200 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x0032 100 253 000 Old_age Always - 0
202 Data_Address_Mark_Errs 0x0000 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36 occurred at disk power-on lifetime: 14573 hours (607 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 58 0c c1 e0 Error: UNC at LBA = 0x00c10c58 = 12651608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 58 0c c1 e0 00 01:05:50.709 READ DMA EXT
25 00 00 e8 0c c1 e0 00 01:05:50.706 READ DMA EXT
ec 00 00 00 00 00 a0 00 01:05:50.704 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:05:58.995 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 01:05:58.907 IDENTIFY DEVICE
Error 35 occurred at disk power-on lifetime: 14573 hours (607 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 58 0c c1 e0 Error: UNC at LBA = 0x00c10c58 = 12651608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 e8 0b c1 e0 00 01:05:50.709 READ DMA EXT
25 00 00 e8 0a c1 e0 00 01:05:50.706 READ DMA EXT
25 00 00 e8 09 c1 e0 00 01:05:50.704 READ DMA EXT
25 00 80 68 09 c1 e0 00 01:05:50.701 READ DMA EXT
25 00 40 28 09 c1 e0 00 01:05:50.697 READ DMA EXT
Error 34 occurred at disk power-on lifetime: 14572 hours (607 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 58 0c c1 e0 Error: UNC at LBA = 0x00c10c58 = 12651608
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 58 0c c1 e0 00 00:02:42.473 READ DMA EXT
25 00 08 50 0c c1 e0 00 00:02:33.060 READ DMA EXT
25 00 08 48 0c c1 e0 00 00:02:32.469 READ DMA EXT
25 00 00 e8 0c c1 e0 00 00:02:32.466 READ DMA EXT
ec 00 00 00 00 00 a0 00 00:02:31.755 IDENTIFY DEVICE
Error 33 occurred at disk power-on lifetime: 14572 hours (607 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 4e 0c c1 e0 Error: UNC at LBA = 0x00c10c4e = 12651598
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 e8 0b c1 e0 00 00:02:31.391 READ DMA EXT
25 00 00 e8 0a c1 e0 00 00:02:33.060 READ DMA EXT
25 00 00 e8 09 c1 e0 00 00:02:32.469 READ DMA EXT
25 00 80 68 09 c1 e0 00 00:02:32.466 READ DMA EXT
25 00 40 28 09 c1 e0 00 00:02:31.755 READ DMA EXT
Error 32 occurred at disk power-on lifetime: 14572 hours (607 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 0c c1 e0 Error: UNC at LBA = 0x00c10c08 = 12651528
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 08 0c c1 e0 00 00:01:26.032 READ DMA EXT
ec 00 00 00 00 00 a0 00 00:01:23.116 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:01:04.625 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 00:01:04.624 IDENTIFY DEVICE
25 00 08 00 0c c1 e0 00 00:01:38.245 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 80% 14572 364973144
# 2 Short offline Completed: read failure 80% 14572 364973144
# 3 Short offline Completed: read failure 80% 14572 364973137
# 4 Short offline Completed: read failure 90% 14572 364973144
# 5 Short offline Completed without error 00% 14541 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Chciałem prosić o pomoc w interpretacji tego logu i o poradę co dalej robić ?
