Mam chyba problem z dyskiem. Nie mogłem znaleźć działu hardware więc umieszczam tu.
Zainstalowałem sobie smartmontools ale niestety nie mogę dojść jak czytać te logi. Tzn domyślam się co czytać ale nie wiem jak interpretować.
Czy może ktoś mógłby mi pomóc w interpretacji albo wskazał jakiś podręcznik gdzie mógłbym sobie o tym poczytać?
Mój log:
Kod: Zaznacz cały
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-23-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Fujitsu MHY BH
Device Model: FUJITSU MHY2120BH
Serial Number: K410T7B2HG45
LU WWN Device Id: 5 00000e 041324dde
Firmware Version: 890B
User Capacity: 120,034,123,776 bytes [120 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3f
Local Time is: Mon Jan 13 14:21:16 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 487) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 69) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 76937
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 27066368
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 7284
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 0 (2000, 0)
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 3322
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 8150
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 253 099 000 Old_age Always - 1
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 5290
182 Erase_Fail_Count_Total 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 253 253 097 Pre-fail Always - 0
185 Unknown_Attribute 0x0010 100 100 000 Old_age Offline - 2
186 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 094 000 Old_age Always - 11424613007366
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 5
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 045 000 Old_age Always - 35 (Min/Max 25/36)
191 G-Sense_Error_Rate 0x0032 253 098 000 Old_age Always - 16580633
192 Power-Off_Retract_Count 0x0032 097 097 000 Old_age Always - 63898575
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 60513
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 1634
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 (0, 5992)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 1997
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 429570720682
240 Transfer_Error_Rate 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 occurred at disk power-on lifetime: 6916 hours (288 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 09 00 00 40 Error: ICRC, ABRT at LBA = 0x00000009 = 9
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 02 00 00 40 00 00:00:02.802 READ DMA EXT
25 03 01 00 00 00 40 00 00:00:02.799 READ DMA EXT
25 03 01 00 00 00 40 00 00:00:02.792 READ DMA EXT
25 03 01 00 00 00 40 00 00:00:02.791 READ DMA EXT
25 03 01 00 00 00 40 00 00:00:02.790 READ DMA EXT
Error 7 occurred at disk power-on lifetime: 6908 hours (287 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d2 06 26 19 e0 Error: UNC 210 sectors at LBA = 0x00192606 = 1648134
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 d8 25 19 e0 08 00:00:52.039 READ DMA EXT
ec 00 00 00 00 00 a0 08 00:00:52.038 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 08 00:00:52.038 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:00:52.037 IDENTIFY DEVICE
25 00 00 d8 25 19 e0 08 00:00:47.038 READ DMA EXT
Error 6 occurred at disk power-on lifetime: 6908 hours (287 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d2 06 26 19 e0 Error: UNC 210 sectors at LBA = 0x00192606 = 1648134
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 d8 25 19 e0 08 00:00:47.038 READ DMA EXT
ec 00 00 00 00 00 a0 08 00:00:47.037 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 08 00:00:47.037 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:00:47.036 IDENTIFY DEVICE
25 00 00 d8 25 19 e0 08 00:00:41.959 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 6908 hours (287 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d2 06 26 19 e0 Error: UNC 210 sectors at LBA = 0x00192606 = 1648134
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 d8 25 19 e0 08 00:00:41.959 READ DMA EXT
ec 00 00 00 00 00 a0 08 00:00:41.959 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 08 00:00:41.959 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:00:41.958 IDENTIFY DEVICE
25 00 00 d8 25 19 e0 08 00:00:36.959 READ DMA EXT
Error 4 occurred at disk power-on lifetime: 6908 hours (287 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d2 06 26 19 e0 Error: UNC 210 sectors at LBA = 0x00192606 = 1648134
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 d8 25 19 e0 08 00:00:36.959 READ DMA EXT
ec 00 00 00 00 00 a0 08 00:00:36.958 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 08 00:00:36.958 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 00:00:36.957 IDENTIFY DEVICE
25 00 00 d8 25 19 e0 08 00:00:31.957 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6384 -
# 2 Short offline Completed without error 00% 6383 -
# 3 Short offline Aborted by host 80% 26 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
