Tutul posta chyba nie do konca oddaje moj problem. Jeszcze z miesiac temu wszystko smigalo jak trzeba na takich samych sterownikach (sterownik to dokladnie iwl3945 instalowany celem zabaw z aircrack-ng). Dzis probujac polaczyc sie przez wifi (a tak sie sklada ze wlasciwie rzadko to robie) karta polaczyla sie z routerem, net byl doslownie na zaladowanie 2 stron i polaczenie utracilem. Network Manager pokazywal, ze ciagle jestem zalogowany do sieci. Ale ifconfig pokazuje ze karta jest w monitor mode ktorego w ogole nie moge wylaczyc.
Kod: Zaznacz cały
eth0 Link encap:Ethernet HWaddr 00:16:d4:d8:2a:a1
inet addr:192.168.5.148 Bcast:192.168.5.255 Mask:255.255.255.0
inet6 addr: fe80::216:d4ff:fed8:2aa1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:78783 errors:0 dropped:0 overruns:0 frame:0
TX packets:47177 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:114406323 (109.1 MB) TX bytes:3877342 (3.6 MB)
Interrupt:219 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4579 errors:0 dropped:0 overruns:0 frame:0
TX packets:4579 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:239923 (234.2 KB) TX bytes:239923 (234.2 KB)
wlan0 Link encap:Ethernet HWaddr 00:1b:77:9a:dc:a0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1367 (1.3 KB) TX bytes:5549 (5.4 KB)
wmaster0 Link encap:UNSPEC HWaddr 00-1B-77-9A-DC-A0-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
przy wylaczonej karcie
Kod: Zaznacz cały
[ 976.766871] wlan0: failed to set channel 161 (5805 MHz) for scan
[ 976.766875] wlan0: failed to set channel 165 (5825 MHz) for scan
[ 976.766879] wlan0: failed to restore operationalchannel after scan
[ 978.765667] wlan0: No ProbeResp from current AP 00:1c:f0:84:fb:22 - assume out of range
[ 982.365496] r8169: eth0: link up
[ 985.360725] iwl3945: Failed to get channel info for channel 153 [3]
[ 1441.282197] UDF-fs: No VRS found
[ 1441.306783] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 1441.308067] ISOFS: changing to secondary root
[ 1808.749645] r8169: eth0: link down
Kod: Zaznacz cały
[ 2812.259452] atkbd.c: Unknown key pressed (translated set 2, code 0xf1 on isa0060/serio0).
[ 2812.259459] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 2812.364022] atkbd.c: Unknown key released (translated set 2, code 0xf1 on isa0060/serio0).
[ 2812.364026] atkbd.c: Use 'setkeycodes e071 <keycode>' to make it known.
[ 2812.487936] iwl3945: Failed to get channel info for channel 153 [3]
[ 2812.487944] iwl3945: Error setting Tx power (-22).
[ 2812.487961] iwl3945: Failed to get channel info for channel 153 [3]
[ 2812.907789] usb 1-2: new full speed USB device using uhci_hcd and address 3
[ 2813.080822] usb 1-2: configuration #1 chosen from 1 choice
[ 2815.119116] ADDRCONF(NETDEV_UP): wlan0: link is not ready