Bluetooth nie działa

[wasalister]

Witam. Jestem świeżo po instalacji Kubuntu na swoim Lenovo G710. Nie działa mi jednak bluetooth i nie jestem w stanie dojść do rozwiązania problemu, mimo kilku dni szukania po sieci. Jedyne rozwiązanie, jakie znalazłem, to postawienie Debiana i instalacja jądra aptosid, ale nie mam czasu, ani ochoty stawiać po raz kolejny systemu, bo instalator systemu wysypuje się na zależnościach. Czy ktoś z was zna rozwiązanie, które pozwoli uruchomić bluetooth na moim lapku. Wersja Kubuntu to 15.10, jądro:

Kod: Zaznacz cały

4.2.0-30-generic

[KamiL]

Masz zainstalowane sterowniki do bluetooth ???

[bear7]

To jest wbudowany Bluetooth? Jak jest rozpoznawany? Otwórz terminal i wykonaj w nim kolejno poniższe polecenia:

Kod: Zaznacz cały

lsusb

Kod: Zaznacz cały

hcitool dev

Kod: Zaznacz cały

hciconfig -a

Kod: Zaznacz cały

sudo service bluetooth status

Kod: Zaznacz cały

ps auxw | grep bluetooth

Kod: Zaznacz cały

lsmod | grep bluetooth

Kod: Zaznacz cały

dmesg | egrep 'bluetooth|hci|err|fail'

Kod: Zaznacz cały

uname -a

Kod: Zaznacz cały

lsb_release -a

Wynik każdego polecenia umieść w oddzielnych znacznikach CODE. Może coś się uda zrobić.

[wasalister]

Bluetooth jest wbudowany. Teraz po kolei:

Kod: Zaznacz cały

lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp. 
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:8008 Intel Corp. 
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 105b:e065 Foxconn International, Inc. BCM43142A0 Bluetooth module
Bus 001 Device 003: ID 5986:0295 Acer, Inc 
Bus 001 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Kod: Zaznacz cały

hcitool dev
Devices:

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ hciconfig -a

Po tym nie pojawia się żaden komunikat

Kod: Zaznacz cały

sudo service bluetooth status
[sudo] hasło użytkownika wasalister: 
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled)
   Active: inactive (dead)
     Docs: man:bluetoothd(8)

Kod: Zaznacz cały

ps auxw | grep bluetooth
wasalis+  1654  0.0  0.0  10736  2188 pts/1    S+   02:25   0:00 grep bluetooth

Kod: Zaznacz cały

lsmod | grep bluetooth
bluetooth             516096  0

Kod: Zaznacz cały

dmesg | egrep 'bluetooth|hci|err|fail'
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.122690] perf_event_intel: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.162598] ACPI: Using IOAPIC for interrupt routing
[    0.219247] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219288] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219326] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219366] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219405] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219442] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219479] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.219517] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.739848] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[    0.739850] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    0.739870] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[    0.739871] pci 0000:07:00.0: Signaling PME through PCIe PME interrupt
[    0.739892] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[    0.739893] pci 0000:08:00.0: Signaling PME through PCIe PME interrupt
[    0.750307] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.750312] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    0.751387] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[    0.751394] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.751471] usb usb1: Manufacturer: Linux 4.2.0-30-generic xhci-hcd
[    0.754544] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.754548] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    0.754584] usb usb2: Manufacturer: Linux 4.2.0-30-generic xhci-hcd
[    0.755318] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.755323] ehci-pci: EHCI PCI platform driver
[    0.755414] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    0.755419] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.755430] ehci-pci 0000:00:1a.0: debug port 2
[    0.759339] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    0.759348] ehci-pci 0000:00:1a.0: irq 16, io mem 0xd161d000
[    0.768739] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.768772] usb usb3: Manufacturer: Linux 4.2.0-30-generic ehci_hcd
[    0.769062] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    0.769066] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 4
[    0.769075] ehci-pci 0000:00:1d.0: debug port 2
[    0.772961] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    0.772970] ehci-pci 0000:00:1d.0: irq 23, io mem 0xd161c000
[    0.784751] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.784782] usb usb4: Manufacturer: Linux 4.2.0-30-generic ehci_hcd
[    0.785059] ehci-platform: EHCI generic platform driver
[    0.785069] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.785078] ohci-pci: OHCI PCI platform driver
[    0.785088] ohci-platform: OHCI generic platform driver
[    0.785095] uhci_hcd: USB Universal Host Controller Interface driver
[    0.883673] ahci 0000:00:1f.2: version 3.0
[    0.884280] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x14 impl SATA mode
[    0.884284] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ems apst 
[    0.890488] scsi host0: ahci
[    0.891414] scsi host1: ahci
[    0.891540] scsi host2: ahci
[    0.891802] scsi host3: ahci
[    0.891924] scsi host4: ahci
[    0.934993] ACPI Error: [\_SB_.PCI0.GFX0.DD02._BCL] Namespace lookup failure, AE_NOT_FOUND (20150619/psargs-359)
[    0.934999] ACPI Error: Method parse/execution failed [\_SB_.PCI0.PEG0.PEGP.DD02._BCL] (Node ffff8802568f55a0), AE_NOT_FOUND (20150619/psparse-536)
[    1.065055] usb 1-4: new high-speed USB device number 2 using xhci_hcd
[    1.081062] usb 3-1: new high-speed USB device number 2 using ehci-pci
[    1.097065] usb 4-1: new high-speed USB device number 2 using ehci-pci
[    1.361231] usb 1-5: new high-speed USB device number 3 using xhci_hcd
[    1.665530] usb 1-8: new full-speed USB device number 4 using xhci_hcd
[   12.510354] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[   12.962627] wl: module verification failed: signature and/or required key missing - tainting kernel

Kod: Zaznacz cały

uname -a
Linux wasalister-Lenovo-G710 4.2.0-30-generic #36-Ubuntu SMP Fri Feb 26 00:58:07 UTC 2016 x86_64 x86_64 x86_64 GNU/Linux

Kod: Zaznacz cały

lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description:    Ubuntu 15.10
Release:        15.10
Codename:       wily

[ilin]

Musi mieć jądro minimum 4.4.
Od tej wersji jest ten model dopiero wspierany.

Jeśli jest takowe dla ubuntu to podajcie jak ma je zainstalować.

[wasalister]

Próbowałem kompilować, ale za cienki bolek na taką zabawę jestem

[ilin]

Dla ubuntu też powinny być jakieś mniej oficjalne paczki z tym kernelem.
Ja nie mam wiedzy na ten temat gdzie ich szukać.
Musi podpowiedzieć ktoś kto ubuntu używa.

P.S.Zabrałem głos dlatego żeby nie wałkować problemu od początku i ubijać piany.
Metoda rozwiązania problemu jest znana.
Zostały tylko sprawy techniczne związane z niuansami danej dystrybucji.

DOPISEK
http://ubuntuhandbook.org/index.php/201 ... in-ubuntu/

Znalezione w sieci.

[wasalister]

Jajko postawione, GRUB automatycznie przestawił się na nowe, Bluetooth Wizard pojawił się na pasku,ale nie może znaleźć urządzeń. Poza tym wifi przestało działać

[ilin]

Odniosę się tylko do wifi.
Musisz przeinstalować sterownik broadcoma.

Bluetooth pewnie trzeba sparować,skonfigurować.
Ważne że urządzenie się pojawiło bo przedtem wcale go w systemie nie było.

[wasalister]

Zainstalowałem wszystko jeszcze raz, od nowa i wifi zaczęło działać, ale tym razem bluetooth znowu nie znajduje adapterów. Wszytko jest tak, jak na starym jajku, mimo, że jedzie na nowym.
Wklejam jeszcze raz wszystkie komendy po kolei:

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ lsusb
Bus 002 Device 002: ID 8087:8000 Intel Corp. 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 004: ID 105b:e065 Foxconn International, Inc. BCM43142A0 Bluetooth module
Bus 003 Device 003: ID 5986:0295 Acer, Inc 
Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ hcitool dev
Devices:
        hci0    00:71:CC:90:18:EC

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ hciconfig -a
hci0:   Type: BR/EDR  Bus: USB
        BD Address: 00:71:CC:90:18:EC  ACL MTU: 1021:8  SCO MTU: 64:1
        UP RUNNING 
        RX bytes:880 acl:0 sco:0 events:36 errors:0
        TX bytes:386 acl:0 sco:0 commands:36 errors:0
        Features: 0xff 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
        Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 
        Link policy: RSWITCH HOLD SNIFF 
        Link mode: SLAVE ACCEPT 
        Name: 'wasalister-Lenovo-G710'
        Class: 0x000000
        Service Classes: Unspecified
        Device Class: Miscellaneous, 
        HCI Version: 4.0 (0x6)  Revision: 0x0
        LMP Version: 4.0 (0x6)  Subversion: 0x210b
        Manufacturer: Broadcom Corporation (15)

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ sudo service bluetooth status
[sudo] hasło użytkownika wasalister: 
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled)
   Active: active (running) since nie 2016-03-06 10:02:14 CET; 7min ago
     Docs: man:bluetoothd(8)
 Main PID: 1040 (bluetoothd)
   Status: "Running"
   CGroup: /system.slice/bluetooth.service
           └─1040 /usr/lib/bluetooth/bluetoothd

mar 06 10:02:14 wasalister-Lenovo-G710 systemd[1]: Starting Bluetooth service...
mar 06 10:02:14 wasalister-Lenovo-G710 bluetoothd[1040]: Bluetooth daemon 5.35
mar 06 10:02:14 wasalister-Lenovo-G710 systemd[1]: Started Bluetooth service.
mar 06 10:02:14 wasalister-Lenovo-G710 bluetoothd[1040]: Starting SDP server
mar 06 10:02:14 wasalister-Lenovo-G710 bluetoothd[1040]: Bluetooth management interface 1.10 initialized

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ ps auxw | grep bluetooth
root      1040  0.0  0.0  29704  4384 ?        Ss   10:02   0:00 /usr/lib/bluetooth/bluetoothd
wasalis+  1899  0.0  0.0  10740  2168 pts/1    S+   10:10   0:00 grep bluetooth

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ dmesg | egrep 'bluetooth|hci|err|fail'
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.127503] perf_event_intel: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[    0.191310] ACPI: Using IOAPIC for interrupt routing
[    0.248007] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248049] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248089] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248128] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248168] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248206] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248245] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.248283] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.782166] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[    0.782168] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[    0.782189] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[    0.782191] pci 0000:07:00.0: Signaling PME through PCIe PME interrupt
[    0.782212] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[    0.782213] pci 0000:08:00.0: Signaling PME through PCIe PME interrupt
[    0.800495] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.800499] ehci-pci: EHCI PCI platform driver
[    0.800607] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    0.800613] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.800624] ehci-pci 0000:00:1a.0: debug port 2
[    0.804512] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    0.804522] ehci-pci 0000:00:1a.0: irq 16, io mem 0xd161d000
[    0.814065] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.814102] usb usb1: Manufacturer: Linux 4.4.0-040400-generic ehci_hcd
[    0.814396] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    0.814401] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.814410] ehci-pci 0000:00:1d.0: debug port 2
[    0.818305] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    0.818313] ehci-pci 0000:00:1d.0: irq 23, io mem 0xd161c000
[    0.830115] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.830173] usb usb2: Manufacturer: Linux 4.4.0-040400-generic ehci_hcd
[    0.830431] ehci-platform: EHCI generic platform driver
[    0.830447] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.830451] ohci-pci: OHCI PCI platform driver
[    0.830462] ohci-platform: OHCI generic platform driver
[    0.830470] uhci_hcd: USB Universal Host Controller Interface driver
[    0.830607] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.830612] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[    0.831694] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[    0.831699] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    0.831835] usb usb3: Manufacturer: Linux 4.4.0-040400-generic xhci-hcd
[    0.834991] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    0.834994] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[    0.835027] usb usb4: Manufacturer: Linux 4.4.0-040400-generic xhci-hcd
[    0.933382] ahci 0000:00:1f.2: version 3.0
[    0.933577] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x14 impl SATA mode
[    0.933582] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part ems apst 
[    0.942486] scsi host0: ahci
[    0.944634] scsi host1: ahci
[    0.944784] scsi host2: ahci
[    0.945046] scsi host3: ahci
[    0.945163] scsi host4: ahci
[    0.997992] ACPI Error: [\_SB_.PCI0.GFX0.DD02._BCL] Namespace lookup failure, AE_NOT_FOUND (20150930/psargs-359)
[    0.997998] ACPI Error: Method parse/execution failed [\_SB.PCI0.PEG0.PEGP.DD02._BCL] (Node ffff8802568f95a0), AE_NOT_FOUND (20150930/psparse-542)
[    1.126137] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.142111] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.150123] usb 3-4: new high-speed USB device number 2 using xhci_hcd
[    1.446126] usb 3-5: new high-speed USB device number 3 using xhci_hcd
[    1.750134] usb 3-8: new full-speed USB device number 4 using xhci_hcd
[    7.000276] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[    8.909684] wl: module verification failed: signature and/or required key missing - tainting kernel
[   12.486355] Bluetooth: hci0 command 0x1001 tx timeout
[   20.486519] Bluetooth: hci0: BCM: Reading local version info failed (-110)
[   20.491567] Bluetooth: hci0: BCM: chip id 70
[   20.507584] Bluetooth: hci0: wasalister-Lenovo-G710
[   20.507600] Bluetooth: hci0: BCM (001.001.011) build 0000
[   20.677814] bluetooth hci0: Direct firmware load for brcm/BCM.hcd failed with error -2
[   20.677820] Bluetooth: hci0: BCM: Patch brcm/BCM.hcd not found

Kod: Zaznacz cały

wasalister@wasalister-Lenovo-G710:~$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description:    Ubuntu 15.10
Release:        15.10
Codename:       wily

[bear7]

Na launchpadzie wisi zgłoszenie dotyczące tego bluetootha. W komentarzach podane są kroki, które pozwalają uruchomić ten moduł: https://bugs.launchpad.net/ubuntu/+sour ... ug/1065400