AverMedia TVphone 98, bt848 - nie dziala.

[COVERek]

Witam.
Mam karte na chipsecie bt848 i cos jest nietak.
Mianowicie programy od tv nie widza jej w ogole, xawtv odbiera obraz... z kamery (mimo ze nie dziala tam gdzie potrzeba - skype). Nie ma nawet wyboru na zmiane urzadzenie wejsciowego. Karta tv jest na /dev/video1, a kamera internetowa na /dev/video0. czy moze tak byc ze te dwa urzadzenie sie ze soba gryza? chcialem jakos zadzialac za pomaca tego tematu, ale niestey nie moge usunac z modprobe bo niby karta jest w uzyciu.. :/ da sie ten problem rozwiazac i sprawic by karta cudownie zadzialala?

Kod: Zaznacz cały

root@box:/home/coverek# rmmod bttv
ERROR: Module bttv is in use by bt878

Kod: Zaznacz cały

02:01.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
        Subsystem: Avermedia Technologies Inc Unknown device 0001
        Flags: bus master, medium devsel, latency 32, IRQ 21
        Memory at f8001000 (32-bit, prefetchable) [size=4K]

02:01.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
        Subsystem: Avermedia Technologies Inc Unknown device 0001
        Flags: medium devsel, IRQ 21
        Memory at f8000000 (32-bit, prefetchable) [size=4K]

Kod: Zaznacz cały

coverek@box:~$ dmesg | grep card
[   32.325700] isapnp: Scanning for PnP cards...
[   32.714421] EISA: Detected 0 cards.
[   46.436165] bttv: Bt8xx card found (0).
[   46.436219] bttv0: detected: AVerMedia TVPhone98 [card=41], PCI subsystem ID is 1461:0001
[   46.436224] bttv0: using: AVerMedia TVPhone 98 [card=41,insmod option]
[   46.656874] input: bttv IR (card=41) as /class/input/input5
[   46.735828] bt878_probe: card id=[0x11461], Unknown card.

[grymberg]

ERROR: Module bttv is in use by bt878

Po prostu wcześniej usuń moduł bt878 zanim usuniesz bttv. Dalej próbuj jak w HowTo

[COVERek]

nic to nie zmienilo niestety... dalej nic.

[ilin]

Dopisz sobie do /etc/modprobe.d/aliases

Kod: Zaznacz cały

alias char-major-81 videodev
alias char-major-81-0 bttv
options bttv card=41 tuner=0

Zrob restart i pokaż co pokazuje wynik polecenia

Kod: Zaznacz cały

xawtv -hwscan

P.S.Nie wiem jaki tam jest tuner więc strzelam na ślepo 0

Pozdrawiam

[COVERek]

sytuacja bez zmian, nie widzi video1. ;/

Kod: Zaznacz cały

coverek@box:~$ xawtv -hwscan
This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.22-14-generic)
looking for available devices
port 48-79
    type : Xvideo, image scaler
    name : Xgl Generic Texture Video

ioctl: VIDIOC_QUERYCAP(driver="";card="";bus_info="";version=0.0.0;capabilities=0x0 []): Unknown error 515
/dev/video0: OK                         [ -device /dev/video0 ]
    type : v4l
    name : Logitech QuickCam USB
    flags:  capture  

/dev/video1: OK                         [ -device /dev/video1 ]
    type : v4l2
    name : BT878 video (AVerMedia TVPhone 
    flags: overlay capture tuner 

p.s. zawsze mi sie wydawalo ze mam bt848.

[ilin]

Jak nie widzi?

Przeciez masz kartę tv pod /dev/video1 pod /dev/video0 masz kamerę internetową
Czego jeszcze chcesz.

[COVERek]

brakuje opcji na zmiane zrodla obrazu.

[ilin]

To chyba xawtv na zrzucie.

Odpalasz to poleceniem

Kod: Zaznacz cały

xawtv -c /dev/video1 -C /dev/dsp

?

[COVERek]

tak, xawtv. efekt jest taki po wpisaniu polecenia.

Kod: Zaznacz cały

coverek@box:~$ xawtv -c /dev/video1 -C /dev/dsp
This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.22-14-generic)
WARNING: Your X-Server has no DGA support.
WARNING: couldn't find framebuffer base address, try manual
         configuration ("v4l-conf -a <addr>")
Warning: Cannot convert string "-*-ledfixed-medium-r-*--39-*-*-*-c-*-*-*" to type FontStruct
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument
...

[ilin]

To tak

Kod: Zaznacz cały

xawtv -c /dev/video1 -C /dev/dsp -nodga

[COVERek]

dalej nic.

Kod: Zaznacz cały

coverek@box:~$ xawtv -c /dev/video1 -C /dev/dsp -nodga
This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.22-14-generic)
WARNING: Your X-Server has no DGA support.
WARNING: couldn't find framebuffer base address, try manual
         configuration ("v4l-conf -a <addr>")
Warning: Cannot convert string "-*-ledfixed-medium-r-*--39-*-*-*-c-*-*-*" to type FontStruct
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument
ioctl: VIDIOC_OVERLAY(int=1): Invalid argument

[ilin]

Pokaż tę częsć /var/log/dmesg która mowi o karcie tv.

[COVERek]

to chyba to bedzie.

Kod: Zaznacz cały

[   53.818329] Linux video capture interface: v2.00
[   54.006200] quickcam: QuickCam USB camera found (driver version QuickCam USB 0.6.6 $Date: 2006/11/04 08:38:14 $)
[   54.006208] quickcam: Kernel:2.6.22-14-generic bus:2 class:FF subclass:FF vendor:046D product:0870
[   54.014948] quickcam: Sensor HDCS-1020 detected
[   54.017033] quickcam: Registered device: /dev/video0
[   54.017086] usbcore: registered new interface driver quickcam
[   54.019808] bttv: driver version 0.9.17 loaded
[   54.019813] bttv: using 8 buffers with 2080k (520 pages) each for capture
[   54.019960] bttv: Bt8xx card found (0).
[   54.019995] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[   54.020020] bttv0: Bt878 (rev 2) at 0000:02:01.0, irq: 21, latency: 32, mmio: 0xf8001000
[   54.020051] bttv0: detected: AVerMedia TVPhone98 [card=41], PCI subsystem ID is 1461:0001
[   54.020058] bttv0: using: AVerMedia TVPhone 98 [card=41,insmod option]
[   54.020106] bttv0: gpio: en=00000000, out=00000000 in=000077c3 [init]
[   54.050688] bttv0: Avermedia eeprom[0x4821]: tuner=5 radio:yes remote control:yes
[   54.050694] bttv0: using tuner=0
[   54.050770] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[   54.051352] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[   54.051927] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[   54.107960] bt878: Unknown symbol bttv_read_gpio
[   54.108024] bt878: Unknown symbol bttv_write_gpio
[   54.108085] bt878: Unknown symbol bttv_gpio_enable
[   54.108494] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[   54.159210] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
[   54.159242] tuner 0-0061: type set to 0 (Temic PAL (4002 FH5))
[   54.159246] tuner 0-0061: type set to 0 (Temic PAL (4002 FH5))
[   54.167528] bttv0: registered device video1
[   54.167558] bttv0: registered device vbi0
[   54.167628] bttv0: registered device radio0
[   54.167653] bttv0: PLL: 28636363 => 35468950 .. ok
[   54.199754] input: bttv IR (card=41) as /class/input/input6

[ilin]

Widzę ze tam wykrywa ci nr tunera 5.
Przestaw wiec w tym wpisie z 0 na 5.

Restart próbuj odpalać.
Jak nie zadziała to odepnij kamerę i wtedy karta powinna się pod /dev/video0 pojawic.
Zobacz czy wtedy zagada.

Kamerą sie bedziemy martwic poźniej.

[COVERek]

kamera odpieta, wpis na tuner=5 zmieniony. dalej kaszana.

[ilin]

kamera odpieta, wpis na tuner=5 zmieniony. dalej kaszana.

I co ja mam z tego wiedzieć?
Nie siedzę przed twym kompem abym mogł przeczytac jakie są objawy i logi.

Pozdrawiam

[COVERek]

napisz mi co mam Ci wyswietlic, to to zrobie.

[ilin]

dmesg , xawtv -hwscan i co się dzieje po odpaleniu xawtv plus wypisy z konsoli.

Wszystko było to juz wyzej ale to wraz z wprowadzanymi zmianami sie zmienia i muszę widziec to na bieząco.

[COVERek]

z przyczyn zwiazanych z karta grafiki musialem zrobic reinstall systemu, ale problem tv pozostal.
oto wyniki...

Kod: Zaznacz cały

coverek@box:~$ dmesg
...
[   39.374425] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[   39.374440] bttv0: Bt878 (rev 2) at 0000:02:01.0, irq: 21, latency: 32, mmio: 0xf8001000
[   39.374454] bttv0: detected: AVerMedia TVPhone98 [card=41], PCI subsystem ID is 1461:0001
[   39.374460] bttv0: using: AVerMedia TVPhone 98 [card=41,autodetected]
[   39.374493] bttv0: gpio: en=00000000, out=00000000 in=000477c3 [init]
[   39.404666] bttv0: Avermedia eeprom[0x4821]: tuner=5 radio:yes remote control:yes
[   39.404672] bttv0: using tuner=5
[   39.404744] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[   39.412507] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[   39.413091] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[   39.461360] intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
[   39.461363]  don't want to <4>intel_rng: disable this in firmware setup, and <4>intel_rng: if
[   39.461365]  you are certain that your <4>intel_rng: system has a functional
[   39.461366]  RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
[   39.582338] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[   39.599732] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7104
[   39.599765] usbcore: registered new interface driver usblp
[   39.599770] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[   39.796919] nvidia: module license 'NVIDIA' taints kernel.
[   40.073610] usbcore: registered new interface driver xpad
[   40.073617] /build/buildd/linux-source-2.6.22-2.6.22/drivers/input/joystick/xpad.c: driver for Xbox controllers v0.1.6
[   40.138834] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
[   40.138892] tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
[   40.138899] tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
[   40.158282] bttv0: registered device video0
[   40.158314] bttv0: registered device vbi0
[   40.158348] bttv0: registered device radio0
[   40.158372] bttv0: PLL: 28636363 => 35468950 .. ok
[   40.188760] input: bttv IR (card=41) as /class/input/input5
[   40.188853] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   40.189030] NVRM: loading NVIDIA UNIX x86 Kernel Module  169.07  Thu Dec 13 18:42:56 PST 2007
[   40.257137] bt878: AUDIO driver version 0.0.0 loaded
[   40.257185] bt878: Bt878 AUDIO function found (0).
[   40.257198] ACPI: PCI Interrupt 0000:02:01.1[A] -> GSI 22 (level, low) -> IRQ 21
[   40.257207] bt878_probe: card id=[0x11461], Unknown card.

Kod: Zaznacz cały

coverek@box:~$ xawtv -c /dev/video0 -C /dev/dsp
[: 12: (opcode:: unexpected operator
This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.22-14-generic)
xinerama 0: 1280x1024+0+0
X Error of failed request:  XF86DGANoDirectVideoMode
  Major opcode of failed request:  137 (XFree86-DGA)
  Minor opcode of failed request:  1 (XF86DGAGetVideoLL)
  Serial number of failed request:  67
  Current serial number in output stream:  67

Kod: Zaznacz cały

coverek@box:~$ xawtv -hwscan
[: 12: (opcode:: unexpected operator
This is xawtv-3.95.dfsg.1, running on Linux/i686 (2.6.22-14-generic)
looking for available devices
port 355-386
    type : Xvideo, image scaler
    name : NV17 Video Texture

port 387-418
    type : Xvideo, image scaler
    name : NV05 Video Blitter

/dev/video0: OK                         [ -device /dev/video0 ]
    type : v4l2
    name : BT878 video (AVerMedia TVPhone 
    flags: overlay capture tuner 

[ilin]

Ale co się konkretnie dzieje po odpaleniu xawtv bo takie wypisy z konsoli to normalne.

Pozdrawiam