skystar2 + czytnik phoenix

[wardek]

Witam

Posiadam tuner satelitarny skystar 2, rev2.8a i czytnik phoenix. Jakiego oprogramowania potrzebuję i jak je skonfigurować aby oglądać telewizję na kartę? Wyczytałem w necie, że można użyć Kaffeine z wtyczką kaffeine-sc i serwera newcs. Próbowałem tak zrobić ale kaffeine nie wykrywa wtyczki, próbowałem różnych wersji kaffeine. Czy istnieje inne oprogramowanie, którego mógłbym użyć albo jak zmusić kaffeine żeby "zobaczył" wtyczkę sc?

EDIT:
Ok, udało mi się uruchomić wtyczkę kaffeine-sc, ale jak to teraz wszystko skonfigurować?

[wardek]

Po odpaleniu Newcs dostaję:

This is NewCS 1.60 - the New CardServer by the Butter-team..
Compiled on May 19 2008 at 21:02:57
Reading Config file from /etc/newcs.xml
TCP-log password is enabled, set to: NewCSpwd
TCP-log set to simple mode
level: normal
type: init
output: console,tcp
logger config: level 1 type 3 output 5
Console log options: level 1 type 3
TCP log options: level 1 type 3
[ 17:22:32 ] [ Box detect ] Box type 1 (General Boxtype - PC compatible)
[ 17:22:32 ] [ Config ] Value in <ipk> for device 0 (Phoenix Interface) is INVALID, skipping...
[ 17:22:32 ] [ Config ] Value in <ucpk> for device 0 (Phoenix Interface) is INVALID, skipping...
[ 17:22:32 ] [ Config ] Pincode for device 0 (Phoenix Interface): 0000
[ 17:22:32 ] [ Config ] /dev/ttyUSB0 ECM priority: round
[ 17:22:32 ] [ EMM Cache ] Initialising dynamic Cache
[ 17:22:32 ] [ ECM Cache ] Initialising dynamic Cache
[ NewCS ] Process ID is: 3573
[ 17:22:32 ] [ Loader ] Starting Telnet on port 1001
[ 17:22:32 ] [ Loader ] Reader type 2 on node /dev/ttyUSB0
[ 17:22:32 ] [ Phoenix ] Opening device /dev/ttyUSB0
[ 17:22:32 ] bind: error! 13: Permission denied
[ 17:22:32 ] [ Phoenix ] Setting Parity to: ODD
[ 17:22:32 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB0
[ 17:22:32 ] [ Phoenix ] Setting Baud to standard 9600
[ 17:22:32 ] [ Phoenix ] Normal RESET on node /dev/ttyUSB0
[ 17:22:33 ] [ ATR ] T=0 1etu=104.17us Guardtime:12etu WWT:9600etu
[ 17:22:33 ] [ ATR ] Historical bytes: 0 B 0 0
[ 17:22:33 ] [ Loader ] Init Conax card
[ 17:22:33 ] [ Phoenix ] Setting Parity to: EVEN
[ 17:22:33 ] [ Phoenix ] Setting 2 Stop bits on node /dev/ttyUSB0
[ 17:22:33 ] [ Phoenix ] Setting Baud to standard 9600
[ 17:22:34 ] [ Keyman ] Adding key 7739254F type 0 on Provider 000000 for caid 0B00 ID=0
[ 17:22:34 ] [ Keyman ] Adding key 3B9C92 type 1 on Provider 000000 for caid 0B00 ID=0
[ 17:22:34 ] [ Loader ] Card 0B00 on port /dev/ttyUSB0 ready
[ 17:22:34 ] [ Loader ] Starting Newcamd Server on port 15000
[ 17:22:34 ] [ Newcamd ] Newcamd thread Server started on port 15000
[ 17:22:34 ] [ NewCS ] Ready to GO!
wardek@wardek-desktop:~$ [ 17:22:34 ] [ Newcamd ] recv: error! 111: Connection refused
[ 17:22:34 ] [ Newcamd:15000 ] User dummy logout

[wardek]

OK, poradziłem sobie.